Hi
I am new to linux. I installed Kubuntu 8.10 but not able to get my wireless to work. I have enabled Broadcom STA drivers.
************************************************** **
The output of iwconfig is like:
eth1 IEEE 802.11 Nickname:""
Access Point: Not-Asssociated
The output of "sudo lshw -C network" is ::
*-network
description: Wireless interface
product: BCM4311 802.11b/g WLAN
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:0c:00.0
logical name: eth1
version: 01
serial: 00:19:7d:af:e7:e5
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=wl latency=0 module=wl multicast=yeswireless=IEEE 802.11bg
*-network
description: Ethernet interface
product: BCM4401-B0 100Base-TX
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 02
serial: 00:15:c5:77:31:8d
size: 10MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=half latency=64 link=no module=ssb multicast=yes port=twisted pair speed=10MB/s
*-network DISABLED
description: Ethernet interface
physical id: 2
logical name: pan0
serial: 76:2d:e8:3f:86:bd
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
************************************************** *******************************
I can see the networks but when I try to connect them, nothing happens. Also in the hardware I can see only Broadcom STA Driver, but first when I opened it I can see both Broadcom STA and Broadcom fw-cutter(B43xx I guess or something like it).
Thanks
Navdeep
I am new to linux. I installed Kubuntu 8.10 but not able to get my wireless to work. I have enabled Broadcom STA drivers.
************************************************** **
The output of iwconfig is like:
eth1 IEEE 802.11 Nickname:""
Access Point: Not-Asssociated
The output of "sudo lshw -C network" is ::
*-network
description: Wireless interface
product: BCM4311 802.11b/g WLAN
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:0c:00.0
logical name: eth1
version: 01
serial: 00:19:7d:af:e7:e5
width: 32 bits
clock: 33MHz
capabilities: pm msi pciexpress bus_master cap_list ethernet physical wireless
configuration: broadcast=yes driver=wl latency=0 module=wl multicast=yeswireless=IEEE 802.11bg
*-network
description: Ethernet interface
product: BCM4401-B0 100Base-TX
vendor: Broadcom Corporation
physical id: 0
bus info: pci@0000:02:00.0
logical name: eth0
version: 02
serial: 00:15:c5:77:31:8d
size: 10MB/s
capacity: 100MB/s
width: 32 bits
clock: 33MHz
capabilities: pm bus_master cap_list ethernet physical mii 10bt 10bt-fd 100bt 100bt-fd autonegotiation
configuration: autonegotiation=on broadcast=yes driver=b44 driverversion=2.0 duplex=half latency=64 link=no module=ssb multicast=yes port=twisted pair speed=10MB/s
*-network DISABLED
description: Ethernet interface
physical id: 2
logical name: pan0
serial: 76:2d:e8:3f:86:bd
capabilities: ethernet physical
configuration: broadcast=yes driver=bridge driverversion=2.3 firmware=N/A link=yes multicast=yes
************************************************** *******************************
I can see the networks but when I try to connect them, nothing happens. Also in the hardware I can see only Broadcom STA Driver, but first when I opened it I can see both Broadcom STA and Broadcom fw-cutter(B43xx I guess or something like it).
Thanks
Navdeep