Wifi Deauthentication codes explained

[GreyGeek]

Linux WiFi: Deauthenticated Reason Codes

Friday 6th July 2012 at 9:58 pm
Written by Adam
So I’ve been having a fiddle with Linux and WiFi this evening in an attempt to make a wifi bridge (Windows can do it so why can’t Linux?)…
Anyway the long and short of it is that I was getting disconnected and de-authenticated from the access point. Having a quick look at dmesg said I was disconnected for “Reason 2″ and “Reason 6″; these on their own are not very helpful and so in a quest to find out what these codes meant, I found that there isn’t a list that’s published anywhere easy to find (a single forum post and in an IEEE pdf). The codes in italics are the most common.

Code	Reason	Explanation
0	Reserved	Normal working operation
1	Unspecific Reason	We don’t know what’s wrong
2	Previous authentication no longer valid	Client has associated but is not authorised.
3	Deauthenticated because sending STA is leaving (or has left) IBSS or ESS	The access point went offline, deauthenticating the client.
4	Disassociated due to inactivity	Client session timeout exceeded.
5	Disassociated because AP is unable to handle all currently associated STAs	The access point is busy, performing load balancing, for example.
6	Class 2 frame received from nonauthenticated STA	Client attempted to transfer data before it was authenticated.
7	Class 3 frame received from nonassociated STA	Client attempted to transfer data before it was associated.
8	Disassociated because sending STA is leaving (or has left) BSS	Operating System moved the client to another access point using non-aggressive load balancing.
9	STA requesting (re)association is not authenticated with responding STA	Client not authorized yet, still attempting to associate with an access point.
10	Disassociated because the information in the Power Capability element is unacceptable
11	Disassociated because the information in the Supported Channels element is unacceptable
12	Reserved	Not Used or Special Purpose
13	Invalid information element.
14	Message integrity code (MIC) failure
15	4-Way Handshake timeout
16	Group Key Handshake timeout
17	Information element in 4-Way Handshake different from (Re)Association Request/Probe Response/Beacon frame
18	Invalid group cipher or Association denied due to requesting STA not supporting all of the data rates in the BSSBasicRateSet parameter	*NEW* The link speed requested by the client or AP is incompatible. (i,e. trying to operate N only speeds on a G AP)
19	Invalid pairwise cipher
20	Invalid AKMP
21	Unsupported RSN information element version
22	Invalid RSN information element capabilities
23	IEEE 802.1X authentication failed
24	Cipher suite rejected because of the security policy
25-31	Reserved	Not Used or Special Purpose
32	Disassociated for unspecified, QoS-related reason	Quality of Service has denied the action.
33	Disassociated because QoS AP lacks sufficient bandwidth for this QoS STA
34	Disassociated because excessive number of frames need to be acknowledged, but are not acknowledged due to AP transmissions and/or poor channel conditions
35	Disassociated because STA is transmitting outside the limits of its TXOPs
36	Requested from peer STA as the STA is leaving the BSS (or resetting)
37	Requested from peer STA as it does not want to use the mechanism
38	Requested from peer STA as the STA received frames using the mechanism for which a setup is required
39	Requested from peer STA due to timeout
45	Peer STA does not support the requested cipher suite
45-65	Reserved	Not Used or Special Purpose
99		Typically “No Reason Code” / Unknown State
535	Reserved	Not Used or Special Purpose

http://www.aboutcher.co.uk/2012/07/l...-reason-codes/

[Feathers McGraw]

This is really handy, thanks for posting Gerry! You'd think info like this would be easy to find (surely lots of people need it?) but it often takes a lot of digging to uncover.