Vinny, is this a desktop computer? I have a couple older Hitachi Deskstar 7K1000.C 1TB drives I'm not using. I'll send them to you if you want. They're installed is my desktop, but I haven't touched them in quite awhile.
No warranty though!
Drive 1:
Drive 2:
No warranty though!
Drive 1:
Code:
[FONT=monospace][COLOR=#54FF54][B]stuart@office[/B][/COLOR][COLOR=#000000]:[/COLOR][COLOR=#5454FF][B]~[/B][/COLOR][COLOR=#000000]$ sudo smartctl --all /dev/sde[/COLOR] smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.8.0-39-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000 Device Model: Hitachi HDS721010KLA330 Serial Number: GTE005PBG7NUTL LU WWN Device Id: 5 000cca 21ec37ccc Firmware Version: GKAOAB0A User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Sat Mar 18 10:21:17 2017 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15354) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 130 130 054 Pre-fail Offline - 151 3 Spin_Up_Time 0x0007 112 112 024 Pre-fail Always - 669 (Average 579) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 458 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 136 136 020 Pre-fail Offline - 31 9 Power_On_Hours 0x0012 091 091 000 Old_age Always - 67105 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 457 192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 1147 193 Load_Cycle_Count 0x0012 100 100 000 Old_age Always - 1147 194 Temperature_Celsius 0x0002 115 115 000 Old_age Always - 52 (Min/Max 15/73) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 180 SMART Error Log Version: 1 ATA Error Count: 180 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 180 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 7f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000007f = 127 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 30 78 00 00 40 08 5d+10:12:35.100 READ FPDMA QUEUED 60 08 d8 38 00 00 40 08 5d+10:12:35.100 READ FPDMA QUEUED ef 10 02 00 00 00 a0 08 5d+10:12:35.100 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 5d+10:12:35.100 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] ec 00 00 00 00 00 a0 08 5d+10:12:35.100 IDENTIFY DEVICE Error 179 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 3f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000003f = 63 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 c8 38 00 00 40 08 5d+10:12:34.800 READ FPDMA QUEUED 60 08 c0 18 00 00 40 08 5d+10:12:34.800 READ FPDMA QUEUED 60 08 b8 00 08 00 40 08 5d+10:12:34.800 READ FPDMA QUEUED 60 08 b0 a0 61 70 40 08 5d+10:12:34.800 READ FPDMA QUEUED 60 08 a8 f8 69 70 40 08 5d+10:12:34.800 READ FPDMA QUEUED Error 178 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 0f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000000f = 15 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 e8 08 00 00 40 08 5d+10:12:34.400 READ FPDMA QUEUED 60 08 e0 00 00 00 40 08 5d+10:12:34.400 READ FPDMA QUEUED 60 08 d8 a0 6d 70 40 08 5d+10:12:34.400 READ FPDMA QUEUED 60 08 d0 00 6d 70 40 08 5d+10:12:34.400 READ FPDMA QUEUED ec 00 01 00 00 00 00 08 5d+10:12:34.400 IDENTIFY DEVICE Error 177 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 17 00 00 40 Error: ICRC, ABRT at LBA = 0x00000017 = 23 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 c8 10 00 00 40 08 5d+10:12:33.800 READ FPDMA QUEUED 60 08 c0 08 00 00 40 08 5d+10:12:33.800 READ FPDMA QUEUED 60 08 b8 00 00 00 40 08 5d+10:12:33.700 READ FPDMA QUEUED ef 10 02 00 00 00 a0 08 5d+10:12:33.700 SET FEATURES [Enable SATA feature] 27 00 00 00 00 00 e0 08 5d+10:12:33.700 READ NATIVE MAX ADDRESS EXT [OBS-ACS-3] Error 176 occurred at disk power-on lifetime: 463 hours (19 days + 7 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 84 51 00 1f 00 00 40 Error: ICRC, ABRT at LBA = 0x0000001f = 31 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- 60 08 18 18 00 00 40 08 5d+10:06:36.000 READ FPDMA QUEUED 60 08 10 00 08 00 40 08 5d+10:06:36.000 READ FPDMA QUEUED 60 08 08 a0 61 70 40 08 5d+10:06:36.000 READ FPDMA QUEUED 60 08 00 f8 69 70 40 08 5d+10:06:36.000 READ FPDMA QUEUED 60 08 f0 d0 69 70 40 08 5d+10:06:36.000 READ FPDMA QUEUED SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Short captive Interrupted (host reset) 30% 485 - # 2 Extended offline Aborted by host 90% 485 - # 3 Extended captive Interrupted (host reset) 90% 485 - # 4 Extended captive Interrupted (host reset) 90% 485 - # 5 Extended captive Interrupted (host reset) 90% 477 - # 6 Short offline Completed without error 00% 52916 - # 7 Extended offline Completed without error 00% 49910 - # 8 Extended offline Completed without error 00% 49910 - # 9 Short offline Completed without error 00% 49899 - #10 Extended offline Completed without error 00% 16555 - #11 Extended offline Completed without error 00% 16387 - #12 Extended offline Completed without error 00% 16219 - #13 Extended offline Completed without error 00% 16051 - #14 Extended offline Completed without error 00% 15883 - #15 Extended offline Completed without error 00% 15715 - #16 Extended offline Completed without error 00% 15547 - #17 Extended offline Completed without error 00% 15380 - #18 Extended offline Completed without error 00% 15214 - #19 Extended offline Completed without error 00% 15044 - #20 Extended offline Completed without error 00% 14877 - #21 Extended offline Completed without error 00% 14707 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. [/FONT]
Code:
[FONT=monospace][COLOR=#54FF54][B]stuart@office[/B][/COLOR][COLOR=#000000]:[/COLOR][COLOR=#5454FF][B]~[/B][/COLOR][COLOR=#000000]$ sudo smartctl --all /dev/sdf[/COLOR] smartctl 6.5 2016-01-24 r4214 [x86_64-linux-4.8.0-39-generic] (local build) Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Hitachi Deskstar 7K1000 Device Model: Hitachi HDS721010KLA330 Serial Number: GTE005PBG7S0GL LU WWN Device Id: 5 000cca 21ec384fe Firmware Version: GKAOAB0A User Capacity: 1,000,204,886,016 bytes [1.00 TB] Sector Size: 512 bytes logical/physical Device is: In smartctl database [for details use: -P show] ATA Version is: ATA/ATAPI-7 T13/1532D revision 1 Local Time is: Sat Mar 18 10:21:59 2017 EDT SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (15354) seconds. Offline data collection capabilities: (0x5b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. No Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 255) minutes. SCT capabilities: (0x003f) SCT Status supported. SCT Error Recovery Control supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000b 100 100 016 Pre-fail Always - 0 2 Throughput_Performance 0x0005 130 130 054 Pre-fail Offline - 150 3 Spin_Up_Time 0x0007 105 105 024 Pre-fail Always - 672 (Average 654) 4 Start_Stop_Count 0x0012 100 100 000 Old_age Always - 460 5 Reallocated_Sector_Ct 0x0033 100 100 005 Pre-fail Always - 0 7 Seek_Error_Rate 0x000b 100 100 067 Pre-fail Always - 0 8 Seek_Time_Performance 0x0005 134 134 020 Pre-fail Offline - 32 9 Power_On_Hours 0x0012 091 091 000 Old_age Always - 67061 10 Spin_Retry_Count 0x0013 100 100 060 Pre-fail Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 455 192 Power-Off_Retract_Count 0x0032 099 099 000 Old_age Always - 1343 193 Load_Cycle_Count 0x0012 099 099 000 Old_age Always - 1343 194 Temperature_Celsius 0x0002 111 111 000 Old_age Always - 54 (Min/Max 15/69) 196 Reallocated_Event_Count 0x0032 100 100 000 Old_age Always - 0 197 Current_Pending_Sector 0x0022 100 100 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0008 100 100 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x000a 200 200 000 Old_age Always - 0 SMART Error Log Version: 1 No Errors Logged SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended captive Interrupted (host reset) 90% 440 - # 2 Short offline Completed without error 00% 52891 - # 3 Extended offline Completed without error 00% 49884 - # 4 Short offline Completed without error 00% 49874 - # 5 Extended offline Completed without error 00% 16530 - # 6 Extended offline Completed without error 00% 16362 - # 7 Extended offline Completed without error 00% 16194 - # 8 Extended offline Completed without error 00% 16026 - # 9 Extended offline Completed without error 00% 15858 - #10 Extended offline Completed without error 00% 15690 - #11 Extended offline Completed without error 00% 15522 - #12 Extended offline Completed without error 00% 15355 - #13 Extended offline Completed without error 00% 15189 - #14 Extended offline Completed without error 00% 15018 - #15 Extended offline Completed without error 00% 14853 - #16 Extended offline Completed without error 00% 14682 - #17 Extended offline Completed without error 00% 14514 - #18 Extended offline Completed without error 00% 14346 - #19 Extended offline Completed without error 00% 14178 - #20 Extended offline Completed without error 00% 13885 - #21 Extended offline Completed without error 00% 13601 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay. [/FONT]
Comment