Announcement

Collapse
No announcement yet.

Built-in wifi not recognized - fresh install on Dell G7

Collapse
X
Collapse
 
  • Page of 1
  • Filter
  • Time
  • Show
Clear All
new posts
Previous template Next
    #1

    Built-in wifi not recognized - fresh install on Dell G7

    Hello - looks like i'm the first to post in this forum ... also my first post in the community so apologize for being long winded. I have a Dell G7 7590 with the
    Intel 9560 2x2 ac (
    Intel 9560 2x2 ac (160 MHz)


    ​built-in Wifi adapter. A little background ... i was running Windows 11 and wifi was working fine. I did a fresh install of Kubuntu 24.04.01 - the wifi adapter was recognized but was unable to get it enabled. Tried a fresh install of Fedora Workstation 40 ... same result and didn't care for the desktop environment. I then tried a fresh install of Mint22 ... no luck and liked KDE Plasmic vs Cinnamon and so decided to do a fresh install of Kubuntu 24.10 - hoping the newer kernel might resolve it. I am liking 24.10 - but unfortunately it appears the wifi adapter is not being recognized at all. All other hardware components seem to be working fine including the wired ethernet adapter.

    I've been searching online for possible resolutions have not found anything that works yet any help would be greatly appreciated.

    I have disabled Secure Boot and set the Windows Fast Boot to minimal in the BIOS. The WIFI switch is enable (doesn't seem to matter either way.) I have the latest firmware available for the laptop installed.

    as you can see here the ethernet is recognized but i don't see the wifi.

    >>>>
    1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
    valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host noprefixroute
    valid_lft forever preferred_lft forever
    2: enp60s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 8c:04:ba:a7:c1:36 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.117/24 brd 192.168.1.255 scope global dynamic noprefixroute enp60s0
    valid_lft 84360sec preferred_lft 84360sec
    inet6 fd02:b153:8efe:c000:e886:7c3e:1b39:4b5b/64 scope global temporary dynamic
    valid_lft 7084sec preferred_lft 3484sec
    inet6 fd02:b153:8efe:c000:4ce9:ae7f:13b2:3c88/64 scope global dynamic mngtmpaddr noprefixroute
    valid_lft 7084sec preferred_lft 3484sec
    inet6 fe80::469e:7a55:216e:dda0/64 scope link noprefixroute
    valid_lft forever preferred_lft forever
    3: virbr0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc noqueue state DOWN group default qlen 1000
    link/ether 52:54:00:d3:de:6d brd ff:ff:ff:ff:ff:ff
    inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0
    valid_lft forever preferred_lft forever
    4: tun0: <POINTOPOINT,MULTICAST,NOARP,UP,LOWER_UP> mtu 1441 qdisc fq_codel state UNKNOWN group default qlen 500
    link/none
    inet 10.41.18.12/24 scope global tun0
    valid_lft forever preferred_lft forever
    inet6 fe80::913e:4d76:e139:37b7/64 scope link stable-privacy proto kernel_ll
    valid_lft forever preferred_lft forever
    <<<<<<<<<<<<<

    /etc/modprobe.d$ lspci
    >>>>>>>
    00:00.0 Host bridge: Intel Corporation 8th Gen Core Processor Host Bridge/DRAM Registers (rev 07)
    00:01.0 PCI bridge: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) (rev 07)
    00:02.0 VGA compatible controller: Intel Corporation CoffeeLake-H GT2 [UHD Graphics 630]
    00:04.0 Signal processing controller: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem (rev 07)
    00:08.0 System peripheral: Intel Corporation Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th/8th Gen Core Processor Gaussian Mixture Model
    00:12.0 Signal processing controller: Intel Corporation Cannon Lake PCH Thermal Controller (rev 10)
    00:14.0 USB controller: Intel Corporation Cannon Lake PCH USB 3.1 xHCI Host Controller (rev 10)
    00:14.2 RAM memory: Intel Corporation Cannon Lake PCH Shared SRAM (rev 10)
    00:15.0 Serial bus controller: Intel Corporation Cannon Lake PCH Serial IO I2C Controller #0 (rev 10)
    00:15.1 Serial bus controller: Intel Corporation Cannon Lake PCH Serial IO I2C Controller #1 (rev 10)
    00:16.0 Communication controller: Intel Corporation Cannon Lake PCH HECI Controller (rev 10)
    00:17.0 SATA controller: Intel Corporation Cannon Lake Mobile PCH SATA AHCI Controller (rev 10)
    00:1b.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #21 (rev f0)
    00:1d.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #9 (rev f0)
    00:1d.5 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #14 (rev f0)
    00:1d.6 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #15 (rev f0)
    00:1f.0 ISA bridge: Intel Corporation HM470 Chipset LPC/eSPI Controller (rev 10)
    00:1f.3 Audio device: Intel Corporation Cannon Lake PCH cAVS (rev 10)
    00:1f.4 SMBus: Intel Corporation Cannon Lake PCH SMBus Controller (rev 10)
    00:1f.5 Serial bus controller: Intel Corporation Cannon Lake PCH SPI Controller (rev 10)
    01:00.0 VGA compatible controller: NVIDIA Corporation TU116M [GeForce GTX 1660 Ti Mobile] (rev a1)
    01:00.1 Audio device: NVIDIA Corporation TU116 High Definition Audio Controller (rev a1)
    01:00.2 USB controller: NVIDIA Corporation TU116 USB 3.1 Host Controller (rev a1)
    01:00.3 Serial bus controller: NVIDIA Corporation TU116 USB Type-C UCSI Controller (rev a1)
    02:00.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    03:00.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    03:01.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    03:02.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    04:00.0 System peripheral: Intel Corporation JHL6340 Thunderbolt 3 NHI (C step) [Alpine Ridge 2C 2016] (rev 02)
    3a:00.0 USB controller: Intel Corporation JHL6340 Thunderbolt 3 USB 3.1 Controller (C step) [Alpine Ridge 2C 2016] (rev 02)
    3b:00.0 Non-Volatile memory controller: KIOXIA Corporation NVMe SSD Controller BG4 (DRAM-less)
    3c:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 2502 (rev 1f)
    ​<<<<<<<<

    I took a look at some of the log files ... here are some things i found that could be of interest ... (one thing i've noticed is the G7 boots up very slow ... once it is up seems to be fine performance wise)

    boot.log
    [^[[0;32m OK ^[[0m] Finished ^[[0;1;39mgrub-common.service^[[0m - Record successful boot for GRUB.^M
    Starting ^[[0;1;39mgrub-initrd-fallback.service^[[0m - GRUB failed boot detection...^M
    ​

    ​kern.log
    2024-10-14T18:38:33.240821-06:00 Congo kernel: No NUMA configuration found
    2024-10-14T18:38:33.240821-06:00 Congo kernel: Faking a node at [mem 0x0000000000000000-0x000000047e7fffff]


    2024-10-14T18:38:33.240958-06:00 Congo kernel: Kernel command line: BOOT_IMAGE=/boot/vmlinuz-6.11.0-8-generic root=UUID=9a3793>
    <9a37935d-b2f7-4155-ac20-498f6bd1bd34 ro quiet splash vt.handoff=7

    2024-10-14T18:38:33.240959-06:00 Congo kernel: Unknown kernel command line parameters "splash BOOT_IMAGE=/boot/vmlinuz-6.11.0->
    <.11.0-8-generic", will be passed to user space.

    2024-10-14T18:38:33.241130-06:00 Congo kernel: MDS CPU bug present and SMT on, data leak possible. See https://www.kernel.org/>
    2024-10-14T18:38:33.241130-06:00 Congo kernel: MMIO Stale Data CPU bug present and SMT on, data leak possible. See https://www>

    2024-10-14T18:38:33.241154-06:00 Congo kernel: audit: initializing netlink subsys (disabled)
    2024-10-14T18:38:33.241154-06:00 Congo kernel: audit: type=2000 audit(1728952685.010:1): state=initialized audit_enabled=0 res=1

    2024-10-14T18:38:33.241168-06:00 Congo kernel: ACPI: Added _OSI(Module Device)
    2024-10-14T18:38:33.241169-06:00 Congo kernel: ACPI: Added _OSI(Processor Device)
    2024-10-14T18:38:33.241169-06:00 Congo kernel: ACPI: Added _OSI(3.0 _SCP Extensions)
    2024-10-14T18:38:33.241170-06:00 Congo kernel: ACPI: Added _OSI(Processor Aggregator Device)
    2024-10-14T18:38:33.241172-06:00 Congo kernel: ACPI: 13 ACPI AML tables successfully acquired and loaded
    2024-10-14T18:38:33.241181-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241182-06:00 Congo kernel: ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
    2024-10-14T18:38:33.241184-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241185-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB82567000 00046F (v02 PmRef Cpu0Cst 00003001 INTL 20160527)
    2024-10-14T18:38:33.241185-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241186-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241186-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB82564800 000581 (v02 PmRef Cpu0Ist 00003000 INTL 20160527)
    2024-10-14T18:38:33.241188-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241189-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241189-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB812B9A00 0000F4 (v02 PmRef Cpu0Psd 00003000 INTL 20160527)
    2024-10-14T18:38:33.241189-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241190-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241190-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB81FC6600 00011B (v02 PmRef Cpu0Hwp 00003000 INTL 20160527)
    2024-10-14T18:38:33.241192-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241192-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241193-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB82563800 000724 (v02 PmRef HwpLvt 00003000 INTL 20160527)
    2024-10-14T18:38:33.241193-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241194-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241194-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB82560000 0005FC (v02 PmRef ApIst 00003000 INTL 20160527)
    2024-10-14T18:38:33.241195-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241197-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241197-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB82698C00 000317 (v02 PmRef ApHwp 00003000 INTL 20160527)
    2024-10-14T18:38:33.241198-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241198-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241199-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB826A1000 000AB0 (v02 PmRef ApPsd 00003000 INTL 20160527)
    2024-10-14T18:38:33.241243-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241252-06:00 Congo kernel: ACPI: Dynamic OEM Table Load:
    2024-10-14T18:38:33.241252-06:00 Congo kernel: ACPI: SSDT 0xFFFF9ADB8269F400 00030A (v02 PmRef ApCst 00003000 INTL 20160527)
    2024-10-14T18:38:33.241256-06:00 Congo kernel: ACPI Error: No pointer back to namespace node in package (____ptrval____) (20240322>
    2024-10-14T18:38:33.241257-06:00 Congo kernel: ACPI: EC: EC started
    2024-10-14T18:38:33.241258-06:00 Congo kernel: ACPI: EC: interrupt blocked
    2024-10-14T18:38:33.241259-06:00 Congo kernel: ACPI: EC: EC_CMD/EC_SC=0x934, EC_DATA=0x930
    2024-10-14T18:38:33.241264-06:00 Congo kernel: ACPI: \_SB_.PCI0.LPCB.ECDV: Boot DSDT EC used to handle transactions
    2024-10-14T18:38:33.241265-06:00 Congo kernel: ACPI: Interpreter enabled
    2024-10-14T18:38:33.241265-06:00 Congo kernel: ACPI: PM: (supports S0 S3 S4 S5)
    2024-10-14T18:38:33.241267-06:00 Congo kernel: ACPI: Using IOAPIC for interrupt routing
    2024-10-14T18:38:33.241272-06:00 Congo kernel: PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report >
    2024-10-14T18:38:33.241272-06:00 Congo kernel: PCI: Ignoring E820 reservations for host bridge windows
    2024-10-14T18:38:33.241273-06:00 Congo kernel: ACPI: Enabled 12 GPEs in block 00 to 7F
    2024-10-14T18:38:33.241273-06:00 Congo kernel: ACPI: \_SB_.PCI0.PEG0.PG00: New power resource
    2024-10-14T18:38:33.241274-06:00 Congo kernel: ACPI: \_SB_.PCI0.RP09.PXP_: New power resource
    2024-10-14T18:38:33.241276-06:00 Congo kernel: ACPI: \_SB_.PCI0.RP21.PXP_: New power resource
    2024-10-14T18:38:33.241276-06:00 Congo kernel: ACPI: \_SB_.PCI0.XDCI.USBC: New power resource
    2024-10-14T18:38:33.241277-06:00 Congo kernel: ACPI: \_SB_.PCI0.PAUD: New power resource
    2024-10-14T18:38:33.241277-06:00 Congo kernel: ACPI: \_SB_.PCI0.SAT0.NVM1.NVPR: New power resource
    2024-10-14T18:38:33.241278-06:00 Congo kernel: ACPI: \_SB_.PCI0.SAT0.VOL0.V0PR: New power resource
    2024-10-14T18:38:33.241283-06:00 Congo kernel: ACPI: \_SB_.PCI0.SAT0.VOL1.V1PR: New power resource
    2024-10-14T18:38:33.241283-06:00 Congo kernel: ACPI: \_SB_.PCI0.SAT0.VOL2.V2PR: New power resource
    2024-10-14T18:38:33.241284-06:00 Congo kernel: ACPI: \_SB_.PCI0.CNVW.WRST: New power resource
    2024-10-14T18:38:33.241286-06:00 Congo kernel: ACPI: \PIN_: New power resource
    2024-10-14T18:38:33.241286-06:00 Congo kernel: ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-7e])
    2024-10-14T18:38:33.241287-06:00 Congo kernel: acpi PNP0A08:00: _OSC: OS supports [ExtendedConfig ASPM ClockPM Segments MSI EDR HP>
    2024-10-14T18:38:33.241287-06:00 Congo kernel: acpi PNP0A08:00: _OSC: platform does not support [AER]

    2024-10-14T18:38:33.242019-06:00 Congo kernel: blacklist: Loading compiled-in revocation X.509 certificates

    2024-10-14T18:38:33.242204-06:00 Congo kernel: usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.

    2024-10-14T18:38:33.242681-06:00 Congo kernel: ACPI Warning: \_SB.PCI0.PEG0.PEGP._DSM: Argument #4 type mismatch - Found [Buffer]
    <ffer], ACPI requires [Package] (20240322/nsarguments-61)


    2024-10-14T18:38:33.242682-06:00 Congo kernel: VGA switcheroo: detected Optimus DSM method \_SB_.PCI0.PEG0.PEGP handle
    2024-10-14T18:38:33.242683-06:00 Congo kernel: nouveau: detected PR support, will not use DSM
    2024-10-14T18:38:33.242688-06:00 Congo kernel: nouveau 0000:01:00.0: enabling device (0006 -> 0007)
    2024-10-14T18:38:33.242689-06:00 Congo kernel: nouveau 0000:01:00.0: NVIDIA TU116 (168000a1)
    2024-10-14T18:38:33.242692-06:00 Congo kernel: nvidia-gpu 0000:01:00.3: i2c timeout error e0000000
    2024-10-14T18:38:33.242696-06:00 Congo kernel: ucsi_ccg 2-0008: i2c_transfer failed -110
    2024-10-14T18:38:33.242697-06:00 Congo kernel: ucsi_ccg 2-0008: ucsi_ccg_init failed - -110
    2024-10-14T18:38:33.242697-06:00 Congo kernel: ucsi_ccg 2-0008: probe with driver ucsi_ccg failed with error -110
    2024-10-14T18:38:33.242698-06:00 Congo kernel: nouveau 0000:01:00.0: bios: version 90.16.20.40.de

    2024-10-14T18:38:33.242789-06:00 Congo kernel: Bluetooth: BNEP (Ethernet Emulation) ver 1.3
    2024-10-14T18:38:33.242791-06:00 Congo kernel: Bluetooth: BNEP filters: protocol multicast
    2024-10-14T18:38:33.242792-06:00 Congo kernel: Bluetooth: BNEP socket layer initialized
    2024-10-14T18:38:33.242792-06:00 Congo kernel: Bluetooth: MGMT ver 1.23
    2024-10-14T18:38:33.242792-06:00 Congo kernel: NET: Registered PF_ALG protocol family
    2024-10-14T18:38:33.812532-06:00 Congo kernel: Bluetooth: RFCOMM TTY layer initialized
    2024-10-14T18:38:33.812558-06:00 Congo kernel: Bluetooth: RFCOMM socket layer initialized
    2024-10-14T18:38:33.812559-06:00 Congo kernel: Bluetooth: RFCOMM ver 1.11
    2024-10-14T18:38:37.636599-06:00 Congo kernel: block nvme0n1: No UUID available providing old NGUID

    024-10-14T18:39:01.293004-06:00 Congo kernel: snd_hda_codec_hdmi hdaudioC0D0: HDMI: pin NID 0x4 not registered
    2024-10-14T18:39:12.318575-06:00 Congo kernel: xhci_hcd 0000:01:00.2: xHC error in resume, USBSTS 0x401, Reinit
    2024-10-14T18:39:12.318585-06:00 Congo kernel: usb usb3: root hub lost power or was reset
    2024-10-14T18:39:12.318586-06:00 Congo kernel: usb usb4: root hub lost power or was reset
    2024-10-14T18:39:21.507083-06:00 Congo kernel: workqueue: pm_runtime_work hogged CPU for >10000us 4 times, consider switching to WQ_UNBOUND

    2024-10-14T18:39:47.259209-06:00 Congo kernel: xhci_hcd 0000:01:00.2: xHC error in resume, USBSTS 0x401, Reinit
    2024-10-14T18:39:47.259221-06:00 Congo kernel: usb usb3: root hub lost power or was reset
    2024-10-14T18:39:47.259223-06:00 Congo kernel: usb usb4: root hub lost power or was reset
    2024-10-14T18:39:47.259243-06:00 Congo kernel: workqueue: pm_runtime_work hogged CPU for >10000us 5 times, consider switching to WQ_UNBOUND
    2024-10-14T18:40:02.110605-06:00 Congo kernel: xhci_hcd 0000:01:00.2: xHC error in resume, USBSTS 0x401, Reinit
    2024-10-14T18:40:02.110618-06:00 Congo kernel: usb usb3: root hub lost power or was reset
    2024-10-14T18:40:02.110620-06:00 Congo kernel: usb usb4: root hub lost power or was reset
    2024-10-14T18:40:02.110623-06:00 Congo kernel: workqueue: pm_runtime_work hogged CPU for >10000us 7 times, consider switching to WQ_UNBOUND
    2024-10-14T18:40:13.893037-06:00 Congo kernel: kauditd_printk_skb: 12649 callbacks suppressed
    ​
    Tags: None
    • Top
    • Bottom
    #2
    When i do a lsusb .... it appears the system sees it ...

    lsusb
    Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 001 Device 002: ID 1ea7:0064 SHARKOON Technologies GmbH 2.4GHz Wireless rechargeable vertical mouse [More&Better]
    Bus 001 Device 003: ID 0bda:565a Realtek Semiconductor Corp. Integrated_Webcam_HD
    Bus 001 Device 004: ID 187c:0550 Alienware Corporation LED controller
    Bus 001 Device 005: ID 8087:0025 Intel Corp. Wireless-AC 9260 Bluetooth Adapter
    Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
    Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
    Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
    Bus 006 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub

    Results of rfkill ...

    rfkill list all
    0: hci0: Bluetooth
    Soft blocked: no
    Hard blocked: no

    ​​results of lspci .... thinking the wifi must be USB 3.1 xHCI Host Controller?

    lspci
    00:00.0 Host bridge: Intel Corporation 8th Gen Core Processor Host Bridge/DRAM Registers (rev 07)
    00:01.0 PCI bridge: Intel Corporation 6th-10th Gen Core Processor PCIe Controller (x16) (rev 07)
    00:02.0 VGA compatible controller: Intel Corporation CoffeeLake-H GT2 [UHD Graphics 630]
    00:04.0 Signal processing controller: Intel Corporation Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem (rev 07)
    00:08.0 System peripheral: Intel Corporation Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th/8th Gen Core Processor Gaussian Mixture Model
    00:12.0 Signal processing controller: Intel Corporation Cannon Lake PCH Thermal Controller (rev 10)
    00:14.0 USB controller: Intel Corporation Cannon Lake PCH USB 3.1 xHCI Host Controller (rev 10)
    00:14.2 RAM memory: Intel Corporation Cannon Lake PCH Shared SRAM (rev 10)
    00:15.0 Serial bus controller: Intel Corporation Cannon Lake PCH Serial IO I2C Controller #0 (rev 10)
    00:15.1 Serial bus controller: Intel Corporation Cannon Lake PCH Serial IO I2C Controller #1 (rev 10)
    00:16.0 Communication controller: Intel Corporation Cannon Lake PCH HECI Controller (rev 10)
    00:17.0 SATA controller: Intel Corporation Cannon Lake Mobile PCH SATA AHCI Controller (rev 10)
    00:1b.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #21 (rev f0)
    00:1d.0 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #9 (rev f0)
    00:1d.5 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #14 (rev f0)
    00:1d.6 PCI bridge: Intel Corporation Cannon Lake PCH PCI Express Root Port #15 (rev f0)
    00:1f.0 ISA bridge: Intel Corporation HM470 Chipset LPC/eSPI Controller (rev 10)
    00:1f.3 Audio device: Intel Corporation Cannon Lake PCH cAVS (rev 10)
    00:1f.4 SMBus: Intel Corporation Cannon Lake PCH SMBus Controller (rev 10)
    00:1f.5 Serial bus controller: Intel Corporation Cannon Lake PCH SPI Controller (rev 10)
    01:00.0 VGA compatible controller: NVIDIA Corporation TU116M [GeForce GTX 1660 Ti Mobile] (rev a1)
    01:00.1 Audio device: NVIDIA Corporation TU116 High Definition Audio Controller (rev a1)
    01:00.2 USB controller: NVIDIA Corporation TU116 USB 3.1 Host Controller (rev a1)
    01:00.3 Serial bus controller: NVIDIA Corporation TU116 USB Type-C UCSI Controller (rev a1)
    02:00.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    03:00.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    03:01.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    03:02.0 PCI bridge: Intel Corporation JHL6340 Thunderbolt 3 Bridge (C step) [Alpine Ridge 2C 2016] (rev 02)
    04:00.0 System peripheral: Intel Corporation JHL6340 Thunderbolt 3 NHI (C step) [Alpine Ridge 2C 2016] (rev 02)
    3a:00.0 USB controller: Intel Corporation JHL6340 Thunderbolt 3 USB 3.1 Controller (C step) [Alpine Ridge 2C 2016] (rev 02)
    3b:00.0 Non-Volatile memory controller: KIOXIA Corporation NVMe SSD Controller BG4 (DRAM-less)
    3c:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. Device 2502 (rev 1f)
    ​
    • Top
    • Bottom

    Comment

      #3
      lsusb shows the Bluetooth component - which is USb based.

      but lspci is NOT showing the WiFi, it isn't detected.

      Don't forget to disable Windows Fast startup - this is not at all related to the BIOS fast boot option. It locks up the Windows drive in a hibernation sort of state, and this can have an effect on hardware, sometimes.
      https://www.windowscentral.com/softw...-on-windows-11
      • Top
      • Bottom

      Comment

        #4
        Thanks for the reply .... i have completely removed Windows11 from the laptop ... not doing a dual-boot configuration - only a linux partition installed.
        • Top
        • Bottom

        Comment

          #5
          Unless there is a physical issue with the card - loose in the socket? - or something in the BIOS, the card would still be detected, I think, even if it were missing a driver (not likely) or there was an issue with its firmware, so this is a bit weird.
          • Top
          • Bottom

          Comment

          Previous template Next
          Working...
          X