MP3 Player Issue

[janthes]

Hi all.

I'm having some trouble connecting to my Samsung YP-T9JAB/XAA mp3 player.

When I connect my player to my computer's USB port, the player shows that it's connected, sometimes digiKam pops up, crashes, and repeats that cycle. That's sometimes, most times, nothing happens.

I tried Adept, typed in "Samsung" and installed "yepp" and "sulu", still nothing.

I tried sudo fdisk -l and it's not showing up too, which is confusing me due to the "connected" message on my player

Any suggestions and/or remedies?

Any remedies?

[shadowfx78]

Re: MP3 Player Issue

Try Amarok, there should be an option in the device section that will work with your player.

My Zen V plus is recognized as a camera as well but still works as a player in amarok.

[mchuskie]

Re: MP3 Player Issue

Plug it in and look at the output of the command 'dmesg' - it should (hopefully) say some things relating to usb and scsi...

[janthes]

Re: MP3 Player Issue

I tried Amarok, but my player doesn't have a manual connect button, so as far as I can see, that's a no go.

As for "dmesg", the relevant data, heres the output:

[75111.918547] sd 6:0:0:0: Attached scsi disk sdc
[75111.918611] sd 6:0:0:0: Attached scsi generic sg3 type 0
[81875.537482] usb 5-8: USB disconnect, address 118
[81887.871158] usb 5-8: new high speed USB device using ehci_hcd and address 119
[81888.007069] usb 5-8: configuration #1 chosen from 1 choice
[81892.604608] usb 5-8: USB disconnect, address 119
[81902.752373] usb 5-8: new high speed USB device using ehci_hcd and address 120
[81902.888348] usb 5-8: configuration #1 chosen from 1 choice
[81908.307348] usb 5-8: USB disconnect, address 120

I'm clueless as to what this means though

[mchuskie]

Re: MP3 Player Issue

[75111.918547] sd 6:0:0:0: Attached scsi disk sdc

Assuming this line comes just after you've plugged in your player, this means your MP3 player's storage is (or should be) available as /dev/sdcn, where n is probably 1. Why KDE doesn't then automount it is our next problem, unless the following applies.

However, I'm curious as to the timestamps in the output you posted... Can you post the whole shebang (it's long, I know) rather than just those lines?

(Tip: If you run dmesg before plugging it in too, you might be able to see where the new lines are added from...)

[janthes]

Re: MP3 Player Issue

When I try to post my dmesg to this forum, I get

The following error or errors occurred while posting this message:
The message exceeds the maximum allowed length (20000 characters).

So I'll beak it don in a few posts.

Part 1:

james@OM3GA:~$ sudo dmesg
[ 0.000000] Linux version 2.6.20-16-generic (root@terranova) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Thu Jun 7 20:19:32 UTC 2007 (Ubuntu 2.6.20-16.29-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000000009fc00 size: 0000000000000400 end: 00000000000a0000 type: 2
[ 0.000000] copy_e820_map() start: 00000000000e8000 size: 0000000000018000 end: 0000000000100000 type: 2
[ 0.000000] copy_e820_map() start: 0000000000100000 size: 000000002feb0000 end: 000000002ffb0000 type: 1
[ 0.000000] copy_e820_map() type is E820_RAM
[ 0.000000] copy_e820_map() start: 000000002ffb0000 size: 0000000000010000 end: 000000002ffc0000 type: 3
[ 0.000000] copy_e820_map() start: 000000002ffc0000 size: 0000000000030000 end: 000000002fff0000 type: 4
[ 0.000000] copy_e820_map() start: 000000002fff0000 size: 0000000000010000 end: 0000000030000000 type: 2
[ 0.000000] copy_e820_map() start: 00000000ffb80000 size: 0000000000480000 end: 0000000100000000 type: 2
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000002ffb0000 (usable)
[ 0.000000] BIOS-e820: 000000002ffb0000 - 000000002ffc0000 (ACPI data)
[ 0.000000] BIOS-e820: 000000002ffc0000 - 000000002fff0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000002fff0000 - 0000000030000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
[ 0.000000] 0MB HIGHMEM available.
[ 0.000000] 767MB LOWMEM available.
[ 0.000000] found SMP MP-table at 000ff780
[ 0.000000] Entering add_active_range(0, 0, 196528) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 196528
[ 0.000000] HighMem 196528 -> 196528
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 196528
[ 0.000000] On node 0 totalpages: 196528
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1503 pages used for memmap
[ 0.000000] Normal zone: 190929 pages, LIFO batch:31
[ 0.000000] HighMem zone: 0 pages used for memmap
[ 0.000000] DMI 2.3 present.
[ 0.000000] ACPI: RSDP (v000 ACPIAM ) @ 0x000fad60
[ 0.000000] ACPI: RSDT (v001 A M I OEMRSDT 0x12000513 MSFT 0x00000097) @ 0x2ffb0000
[ 0.000000] ACPI: FADT (v002 A M I OEMFACP 0x12000513 MSFT 0x00000097) @ 0x2ffb0200
[ 0.000000] ACPI: MADT (v001 A M I OEMAPIC 0x12000513 MSFT 0x00000097) @ 0x2ffb0390
[ 0.000000] ACPI: OEMB (v001 A M I OEMBIOS 0x12000513 MSFT 0x00000097) @ 0x2ffc0040
[ 0.000000] ACPI: DSDT (v001 A0049 A0049000 0x00000000 INTL 0x02002026) @ 0x00000000
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 15:4 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1 15:4 APIC version 20
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 40000000 (gap: 30000000:cfb80000)
[ 0.000000] Detected 3150.223 MHz processor.
[ 28.504992] Built 1 zonelists. Total pages: 194993
[ 28.504997] Kernel command line: root=UUID=3aaae75a-f1e0-48a9-8b2e-e6e8bbfa7481 ro quiet splash
[ 28.505146] mapped APIC to ffffd000 (fee00000)
[ 28.505149] mapped IOAPIC to ffffc000 (fec00000)
[ 28.505151] Enabling fast FPU save and restore... done.
[ 28.505154] Enabling unmasked SIMD FPU exception support... done.
[ 28.505164] Initializing CPU#0
[ 28.505234] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 28.506566] Console: colour VGA+ 80x25
[ 28.507067] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 28.507497] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 28.518892] Memory: 768056k/786112k available (1992k kernel code, 17460k reserved, 900k data, 328k init, 0k highmem)
[ 28.518902] virtual kernel memory layout:
[ 28.518903] fixmap : 0xfff4e000 - 0xfffff000 ( 708 kB)
[ 28.518904] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 28.518905] vmalloc : 0xf0800000 - 0xff7fe000 ( 239 MB)
[ 28.518906] lowmem : 0xc0000000 - 0xeffb0000 ( 767 MB)
[ 28.518907] .init : 0xc03d9000 - 0xc042b000 ( 328 kB)
[ 28.518908] .data : 0xc02f2374 - 0xc03d36d4 ( 900 kB)
[ 28.518909] .text : 0xc0100000 - 0xc02f2374 (1992 kB)
[ 28.518912] Checking if this processor honours the WP bit even in supervisor mode... Ok.
[ 28.597221] Calibrating delay using timer specific routine.. 6304.72 BogoMIPS (lpj=12609443)
[ 28.597258] Security Framework v1.0.0 initialized
[ 28.597264] SELinux: Disabled at boot.
[ 28.597279] Mount-cache hash table entries: 512
[ 28.597397] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
[ 28.597405] monitor/mwait feature present.
[ 28.597406] using mwait in idle threads.
[ 28.597411] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 28.597414] CPU: L2 cache: 1024K
[ 28.597416] CPU: Physical Processor ID: 0
[ 28.597418] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003180 0000441d 00000000 00000000
[ 28.597427] Compat vDSO mapped to ffffe000.
[ 28.597431] Remapping vsyscall page to ffffe000
[ 28.597444] Checking 'hlt' instruction... OK.
[ 28.613298] SMP alternatives: switching to UP code
[ 28.613606] Early unpacking initramfs... done
[ 28.869279] ACPI: Core revision 20060707
[ 28.869424] ACPI: Looking for DSDT in initramfs... file /DSDT.aml not found, using machine DSDT.
[ 28.871194] CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 01
[ 28.871215] SMP alternatives: switching to SMP code
[ 28.871343] Booting processor 1/1 eip 3000
[ 28.881665] Initializing CPU#1
[ 28.961152] Calibrating delay using timer specific routine.. 6300.45 BogoMIPS (lpj=12600919)
[ 28.961161] CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 0000441d 00000000 00000000
[ 28.961168] monitor/mwait feature present.

[janthes]

Re: MP3 Player Issue

Part 2:

[ 28.961173] CPU: Trace cache: 12K uops, L1 D cache: 16K
[ 28.961176] CPU: L2 cache: 1024K
[ 28.961178] CPU: Physical Processor ID: 0
[ 28.961181] CPU: After all inits, caps: bfebfbff 00000000 00000000 00003180 0000441d 00000000 00000000
[ 28.961446] CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 01
[ 28.961486] Total of 2 processors activated (12605.18 BogoMIPS).
[ 28.961613] ENABLING IO-APIC IRQs
[ 28.961789] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 29.109132] checking TSC synchronization across 2 CPUs: passed.
[ 0.003999] Brought up 2 CPUs
[ 0.103409] migration_cost=151
[ 0.103681] Booting paravirtualized kernel on bare hardware
[ 0.103759] Time: 14:29:06 Date: 07/25/107
[ 0.103789] NET: Registered protocol family 16
[ 0.103876] EISA bus registered
[ 0.103881] ACPI: bus type pci registered
[ 0.103943] PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
[ 0.103945] PCI: Using configuration type 1
[ 0.103947] Setting up standard PCI resources
[ 0.117409] ACPI: Interpreter enabled
[ 0.117412] ACPI: Using IOAPIC for interrupt routing
[ 0.118410] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.118417] PCI: Probing PCI hardware (bus 00)
[ 0.118988] PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
[ 0.118992] PCI quirk: region 0480-04bf claimed by ICH4 GPIO
[ 0.119249] Boot video device is 0000:01:00.0
[ 0.119546] PCI: Transparent bridge - 0000:00:1e.0
[ 0.119572] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.128249] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.134461] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.134692] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.134918] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.135146] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.135371] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 12 14 15) *0, disabled.
[ 0.135598] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.135823] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.136061] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.136156] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.136171] pnp: PnP ACPI init
[ 0.140519] pnp: PnP ACPI: found 12 devices
[ 0.140523] ASUS P4P800 detected. Disabling PnPBIOS
[ 0.140525] PnPBIOS: Disabled
[ 0.140579] PCI: Using ACPI for IRQ routing
[ 0.140583] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.144866] NET: Registered protocol family 8
[ 0.144869] NET: Registered protocol family 20
[ 0.145503] pnp: 00:08: ioport range 0x680-0x6ff has been reserved
[ 0.145506] pnp: 00:08: ioport range 0x290-0x297 has been reserved
[ 0.145834] PCI: Bridge: 0000:00:01.0
[ 0.145836] IO window: disabled.
[ 0.145841] MEM window: fc900000-fe9fffff
[ 0.145845] PREFETCH window: dff00000-efefffff
[ 0.145851] PCI: Bridge: 0000:00:1e.0
[ 0.145855] IO window: d000-dfff
[ 0.145861] MEM window: fea00000-feafffff
[ 0.145865] PREFETCH window: 40000000-400fffff
[ 0.145882] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.145914] NET: Registered protocol family 2
[ 0.188032] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.188190] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.188788] TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.189221] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.189224] TCP reno registered
[ 0.200132] checking if image is initramfs... it is
[ 0.707535] Freeing initrd memory: 6785k freed
[ 0.707965] audit: initializing netlink socket (disabled)
[ 0.707979] audit(1188052146.392:1): initialized
[ 0.708158] VFS: Disk quotas dquot_6.5.1
[ 0.708179] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.708230] io scheduler noop registered
[ 0.708233] io scheduler anticipatory registered
[ 0.708235] io scheduler deadline registered
[ 0.708247] io scheduler cfq registered (default)
[ 8.706537] 0000:00:1d.7 EHCI: BIOS handoff failed (BIOS bug ?) 01010001
[ 8.706894] isapnp: Scanning for PnP cards...
[ 9.058560] isapnp: No Plug & Play device found
[ 9.084011] Real Time Clock Driver v1.12ac
[ 9.084060] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 9.084172] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 9.084308] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 9.084839] 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
[ 9.085067] 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
[ 9.085256] mice: PS/2 mouse device common for all mice
[ 9.085870] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 9.086022] input: Macintosh mouse button emulation as /class/input/input0
[ 9.086063] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 9.086067] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 9.086344] PNP: No PS/2 controller found. Probing ports directly.
[ 9.088655] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 9.088661] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 9.088779] EISA: Probing bus 0 at eisa.0
[ 9.088819] EISA: Detected 0 cards.
[ 9.118897] TCP cubic registered
[ 9.118906] NET: Registered protocol family 1
[ 9.118930] Starting balanced_irq
[ 9.118937] Using IPI No-Shortcut mode
[ 9.119017] ACPI: (supports S0 S1 S3 S4 S5)
[ 9.119060] Magic number: 3:302:486
[ 9.119443] Freeing unused kernel memory: 328k freed
[ 9.122289] Time: tsc clocksource has been installed.
[ 10.316523] Capability LSM initialized
[ 10.757814] usbcore: registered new interface driver usbfs
[ 10.757847] usbcore: registered new interface driver hub
[ 10.757880] usbcore: registered new device driver usb
[ 10.759119] USB Universal Host Controller Interface driver v3.0
[ 10.759178] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 10.759192] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 10.759198] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 10.759313] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 10.759341] uhci_hcd 0000:00:1d.0: irq 16, io base 0x0000eec0
[ 10.759470] usb usb1: configuration #1 chosen from 1 choice
[ 10.759506] hub 1-0:1.0: USB hub found
[ 10.759515] hub 1-0:1.0: 2 ports detected
[ 10.862407] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 17
[ 10.862428] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 10.862435] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 10.862467] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 10.862497] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000ef00
[ 10.862638] usb usb2: configuration #1 chosen from 1 choice
[ 10.862675] hub 2-0:1.0: USB hub found
[ 10.862683] hub 2-0:1.0: 2 ports detected
[ 10.874573] SCSI subsystem initialized
[ 10.882680] libata version 2.20 loaded.
[ 10.889720] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver

[janthes]

Re: MP3 Player Issue

Part 3:

[ 10.941146] Floppy drive(s): fd0 is 1.44M
[ 10.961939] FDC 0 is a post-1991 82077
[ 10.966342] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 10.966358] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 10.966365] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 10.966403] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 10.966431] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000ef20
[ 10.966582] usb usb3: configuration #1 chosen from 1 choice
[ 10.966622] hub 3-0:1.0: USB hub found
[ 10.966633] hub 3-0:1.0: 2 ports detected
[ 11.070260] ACPI: PCI Interrupt 0000:00:1d.3[A] -> GSI 16 (level, low) -> IRQ 16
[ 11.070276] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 11.070282] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 11.070317] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 11.070342] uhci_hcd 0000:00:1d.3: irq 16, io base 0x0000ef40
[ 11.070493] usb usb4: configuration #1 chosen from 1 choice
[ 11.070533] hub 4-0:1.0: USB hub found
[ 11.070544] hub 4-0:1.0: 2 ports detected
[ 11.102140] usb 1-1: new low speed USB device using uhci_hcd and address 2
[ 11.174582] ACPI: PCI Interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 19
[ 11.174602] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 11.174608] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 11.174656] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 11.174695] ehci_hcd 0000:00:1d.7: debug port 1
[ 11.174703] PCI: cache line size of 128 is not supported by device 0000:00:1d.7
[ 11.174715] ehci_hcd 0000:00:1d.7: irq 19, io mem 0xfebff800
[ 11.178615] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 11.178950] usb usb5: configuration #1 chosen from 1 choice
[ 11.178988] hub 5-0:1.0: USB hub found
[ 11.178999] hub 5-0:1.0: 8 ports detected
[ 11.282300] ACPI: PCI Interrupt 0000:02:0d.2[C] -> GSI 23 (level, low) -> IRQ 19
[ 11.282318] ehci_hcd 0000:02:0d.2: EHCI Host Controller
[ 11.282355] ehci_hcd 0000:02:0d.2: new USB bus registered, assigned bus number 6
[ 11.306103] ehci_hcd 0000:02:0d.2: irq 19, io mem 0xfeaffc00
[ 11.306112] ehci_hcd 0000:02:0d.2: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 11.306213] usb usb6: configuration #1 chosen from 1 choice
[ 11.306253] hub 6-0:1.0: USB hub found
[ 11.306263] hub 6-0:1.0: 5 ports detected
[ 11.411309] ata_piix 0000:00:1f.1: version 2.10ac1
[ 11.411332] PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
[ 11.411342] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 11.411370] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 11.411456] ata1: PATA max UDMA/133 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001fc00 irq 14
[ 11.411505] ata2: PATA max UDMA/133 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001fc08 irq 15
[ 11.411528] scsi0 : ata_piix
[ 11.574441] ata1.00: ata_hpa_resize 1: sectors = 39102336, hpa_sectors = 39102336
[ 11.574445] ata1.00: ATA-6: ST320014A, 3.13, max UDMA/100
[ 11.574448] ata1.00: 39102336 sectors, multi 16: LBA
[ 11.614413] ata1.00: ata_hpa_resize 1: sectors = 39102336, hpa_sectors = 39102336
[ 11.614416] ata1.00: configured for UDMA/100
[ 11.614427] scsi1 : ata_piix
[ 11.630044] usb 1-1: device not accepting address 2, error -71
[ 11.934220] ata2.00: ATAPI, max UDMA/33
[ 12.098192] ata2.00: configured for UDMA/33
[ 12.098322] scsi 0:0:0:0: Direct-Access ATA ST320014A 3.13 PQ: 0 ANSI: 5
[ 12.100151] scsi 1:0:0:0: CD-ROM _NEC DVD_RW ND-3550A 1.06 PQ: 0 ANSI: 5
[ 12.100747] ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
[ 12.100764] ACPI: PCI Interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
[ 12.100782] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 12.100824] ata3: SATA max UDMA/133 cmd 0x0001eff0 ctl 0x0001efe6 bmdma 0x0001ef90 irq 18
[ 12.100860] ata4: SATA max UDMA/133 cmd 0x0001efa8 ctl 0x0001efe2 bmdma 0x0001ef98 irq 18
[ 12.100871] scsi2 : ata_piix
[ 12.262241] ata3.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
[ 12.262245] ata3.00: ATA-7: WDC WD800JD-00LSA0, 06.01D06, max UDMA/133
[ 12.262247] ata3.00: 156301488 sectors, multi 16: LBA48
[ 12.270220] ata3.00: ata_hpa_resize 1: sectors = 156301488, hpa_sectors = 156301488
[ 12.270223] ata3.00: configured for UDMA/133
[ 12.270232] scsi3 : ata_piix
[ 12.365923] usb 5-5: new high speed USB device using ehci_hcd and address 3
[ 12.436036] ATA: abnormal status 0x7F on port 0x0001efaf
[ 12.436154] scsi 2:0:0:0: Direct-Access ATA WDC WD800JD-00LS 06.0 PQ: 0 ANSI: 5
[ 12.436969] ACPI: PCI Interrupt 0000:02:05.0[A] -> GSI 22 (level, low) -> IRQ 20
[ 12.437013] skge 1.9 addr 0xfeadc000 irq 20 chip Yukon-Lite rev 9
[ 12.437275] skge eth0: addr 00:15:f2:7d:ae:01
[ 12.440621] ACPI: PCI Interrupt 0000:02:0d.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 12.440637] ohci_hcd 0000:02:0d.0: OHCI Host Controller
[ 12.440676] ohci_hcd 0000:02:0d.0: new USB bus registered, assigned bus number 7
[ 12.440694] ohci_hcd 0000:02:0d.0: irq 21, io mem 0xfeafd000
[ 12.502309] usb 5-5: configuration #1 chosen from 1 choice
[ 12.523804] usb usb7: configuration #1 chosen from 1 choice
[ 12.523848] hub 7-0:1.0: USB hub found
[ 12.523859] hub 7-0:1.0: 3 ports detected
[ 12.626013] ACPI: PCI Interrupt 0000:02:0d.1[B] -> GSI 22 (level, low) -> IRQ 20
[ 12.626034] ohci_hcd 0000:02:0d.1: OHCI Host Controller
[ 12.626067] ohci_hcd 0000:02:0d.1: new USB bus registered, assigned bus number 8
[ 12.626083] ohci_hcd 0000:02:0d.1: irq 20, io mem 0xfeafe000
[ 12.711759] usb usb8: configuration #1 chosen from 1 choice
[ 12.711799] hub 8-0:1.0: USB hub found
[ 12.711810] hub 8-0:1.0: 2 ports detected
[ 12.757868] usb 5-8: new high speed USB device using ehci_hcd and address 4
[ 12.835496] SCSI device sda: 39102336 512-byte hdwr sectors (20020 MB)
[ 12.835519] sda: Write Protect is off
[ 12.835522] sda: Mode Sense: 00 3a 00 00
[ 12.835548] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.835616] SCSI device sda: 39102336 512-byte hdwr sectors (20020 MB)
[ 12.835631] sda: Write Protect is off
[ 12.835634] sda: Mode Sense: 00 3a 00 00
[ 12.835658] SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.835664] sda: sda1 sda2 sda3
[ 12.890787] usb 5-8: configuration #1 chosen from 1 choice
[ 12.891189] usbcore: registered new interface driver libusual
[ 12.897904] Initializing USB Mass Storage driver...
[ 12.915455] sd 0:0:0:0: Attached scsi disk sda
[ 12.915640] SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
[ 12.915657] sdb: Write Protect is off
[ 12.915661] sdb: Mode Sense: 00 3a 00 00
[ 12.915687] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.915756] SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
[ 12.915771] sdb: Write Protect is off
[ 12.915774] sdb: Mode Sense: 00 3a 00 00
[ 12.915818] SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 12.915823] sdb:sr0: scsi3-mmc drive: 48x/48x writer cd/rw xa/form2 cdda tray
[ 12.919946] Uniform CD-ROM driver Revision: 3.20
[ 12.919984] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 12.930448] sdb1
[ 12.930499] sd 2:0:0:0: Attached scsi disk sdb
[ 12.935449] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 12.935479] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 12.935509] sd 2:0:0:0: Attached scsi generic sg2 type 0
[ 13.129812] usb 1-1: new low speed USB device using uhci_hcd and address 4
[ 13.307439] usb 1-1: configuration #1 chosen from 1 choice
[ 13.310648] scsi4 : SCSI emulation for USB Mass Storage devices
[ 13.310716] usb-storage: device found at 3
[ 13.310719] usb-storage: waiting for device to settle before scanning
[ 13.310780] scsi5 : SCSI emulation for USB Mass Storage devices
[ 13.310834] usb-storage: device found at 4
[ 13.310837] usb-storage: waiting for device to settle before scanning
[ 13.310855] usbcore: registered new interface driver usb-storage
[ 13.310859] USB Mass Storage support registered.
[ 13.330605] usbcore: registered new interface driver hiddev
[ 13.344445] input: Logitech USB Receiver as /class/input/input1
[ 13.344462] input: USB HID v1.10 Keyboard [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 13.373453] input: Logitech USB Receiver as /class/input/input2
[ 13.373534] input,hiddev96: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.0-1
[ 13.373549] usbcore: registered new interface driver usbhid
[ 13.373553] drivers/usb/input/hid-core.c: v2.6:USB HID core driver
[ 13.404385] Attempting manual resume
[ 13.404389] swsusp: Resume From Partition 8:1
[ 13.404391] PM: Checking swsusp image.
[ 13.404627] PM: Resume from disk failed.
[ 13.428693] kjournald starting. Commit interval 5 seconds
[ 13.428704] EXT3-fs: mounted filesystem with ordered data mode.
[ 18.309125] usb-storage: device scan complete
[ 18.309357] usb-storage: device scan complete
[ 18.309858] scsi 5:0:0:0: Direct-Access IBM-DJSA-220 JS4G PQ: 0 ANSI: 0 CCS
[ 18.310111] scsi 4:0:0:0: Direct-Access Generic STORAGE DEVICE 9325 PQ: 0 ANSI: 0
[ 18.310734] scsi 4:0:0:1: Direct-Access Generic STORAGE DEVICE 9325 PQ: 0 ANSI: 0
[ 18.311090] SCSI device sdc: 39070080 512-byte hdwr sectors (20004 MB)
[ 18.314085] sdc: test WP failed, assume Write Enabled
[ 18.314088] sdc: assuming drive cache: write through
[ 18.314959] SCSI device sdc: 39070080 512-byte hdwr sectors (20004 MB)
[ 18.317958] sdc: test WP failed, assume Write Enabled
[ 18.317961] sdc: assuming drive cache: write through
[ 18.317964] sdc: sdc1

[janthes]

Re: MP3 Player Issue

Part 4

[ 18.685501] sd 5:0:0:0: Attached scsi disk sdc
[ 18.685540] sd 5:0:0:0: Attached scsi generic sg3 type 0
[ 18.686338] sd 4:0:0:0: Attached scsi removable disk sdd
[ 18.686371] sd 4:0:0:0: Attached scsi generic sg4 type 0
[ 18.687335] sd 4:0:0:1: Attached scsi removable disk sde
[ 18.687368] sd 4:0:0:1: Attached scsi generic sg5 type 0
[ 25.663777] skge eth0: enabling interface
[ 26.959087] NET: Registered protocol family 17
[ 27.150350] Linux agpgart interface v0.102 (c) Dave Jones
[ 27.206509] agpgart: Detected an Intel 865 Chipset.
[ 27.211938] agpgart: AGP aperture is 128M @ 0xf0000000
[ 27.216102] iTCO_vendor_support: vendor-support=0
[ 27.484832] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.01 (11-Nov-2006)
[ 27.486052] iTCO_wdt: Found a ICH5 or ICH5R TCO device (Version=1, TCOBASE=0x0860)
[ 27.486108] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 27.517402] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 27.523026] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 27.589345] skge eth0: Link is up at 100 Mbps, full duplex, flow control none
[ 27.737945] intel_rng: FWH not detected
[ 27.980135] input: PC Speaker as /class/input/input3
[ 28.843159] nvidia: module license 'NVIDIA' taints kernel.
[ 29.096827] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 29.097879] NVRM: loading NVIDIA UNIX x86 Kernel Module 100.14.11 Wed Jun 13 18:21:22 PDT 2007
[ 29.213246] ACPI: PCI Interrupt 0000:00:1f.5[B] -> GSI 17 (level, low) -> IRQ 22
[ 29.213274] PCI: Setting latency timer of device 0000:00:1f.5 to 64
[ 29.571027] AC'97 0 analog subsections not ready
[ 29.639018] intel8x0_measure_ac97_clock: measured 56130 usecs
[ 29.639021] intel8x0: clocking to 48000
[ 29.779167] fuse init (API version 7.8)
[ 29.845773] lp: driver loaded but no devices found
[ 29.872735] Adding 1502068k swap on /dev/disk/by-uuid/1567e619-4e0c-4bbf-9ab6-89ad7fc86c3f. Priority:-1 extents:1 across:1502068k
[ 30.153905] EXT3 FS on sda3, internal journal
[ 30.287749] NET: Registered protocol family 10
[ 30.287881] lo: Disabled Privacy Extensions
[ 30.588980] NTFS driver 2.1.28 [Flags: R/O MODULE].
[ 30.638855] NTFS volume version 3.1.
[ 30.732494] kjournald starting. Commit interval 5 seconds
[ 30.732665] EXT3 FS on sda2, internal journal
[ 30.732671] EXT3-fs: mounted filesystem with ordered data mode.
[ 36.281255] input: Power Button (FF) as /class/input/input4
[ 36.281291] ACPI: Power Button (FF) [PWRF]
[ 36.281366] input: Power Button (CM) as /class/input/input5
[ 36.281400] ACPI: Power Button (CM) [PWRB]
[ 36.376187] No dock devices found.
[ 36.442253] Using specific hotkey driver
[ 36.510630] ibm_acpi: ec object not found
[ 36.639489] pcc_acpi: loading...
[ 40.779332] ppdev: user-space parallel port driver
[ 42.412657] apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
[ 42.412664] apm: disabled - APM is not SMP safe.
[ 43.443273] Bluetooth: Core ver 2.11
[ 43.443342] NET: Registered protocol family 31
[ 43.443346] Bluetooth: HCI device and connection manager initialized
[ 43.443350] Bluetooth: HCI socket layer initialized
[ 43.459661] Bluetooth: L2CAP ver 2.8
[ 43.459667] Bluetooth: L2CAP socket layer initialized
[ 43.732749] Bluetooth: RFCOMM socket layer initialized
[ 43.732767] Bluetooth: RFCOMM TTY layer initialized
[ 43.732770] Bluetooth: RFCOMM ver 1.8
[ 46.999925] agpgart: Found an AGP 3.0 compliant device at 0000:00:00.0.
[ 46.999942] agpgart: Putting AGP V3 device at 0000:00:00.0 into 8x mode
[ 46.999978] agpgart: Putting AGP V3 device at 0000:01:00.0 into 8x mode
[ 55.538668] eth0: no IPv6 routers present
[ 1282.688539] usb 5-8: USB disconnect, address 4
[ 2317.250722] usb 5-8: new high speed USB device using ehci_hcd and address 5
[ 2320.329537] usb 5-8: configuration #1 chosen from 1 choice
[ 2320.329781] scsi6 : SCSI emulation for USB Mass Storage devices
[ 2320.330151] usb-storage: device found at 5
[ 2320.330155] usb-storage: waiting for device to settle before scanning
[ 2325.329488] usb-storage: device scan complete
[ 2325.330236] scsi 6:0:0:0: Direct-Access IBM-DJSA-220 JS4G PQ: 0 ANSI: 0 CCS
[ 2325.331589] SCSI device sdc: 39070080 512-byte hdwr sectors (20004 MB)
[ 2325.334586] sdc: test WP failed, assume Write Enabled
[ 2325.334591] sdc: assuming drive cache: write through
[ 2325.335584] SCSI device sdc: 39070080 512-byte hdwr sectors (20004 MB)
[ 2325.338583] sdc: test WP failed, assume Write Enabled
[ 2325.338587] sdc: assuming drive cache: write through
[ 2325.338592] sdc: sdc1
[ 2325.362830] sd 6:0:0:0: Attached scsi disk sdc
[ 2325.362891] sd 6:0:0:0: Attached scsi generic sg3 type 0
[ 2411.762849] usb 1-2: new full speed USB device using uhci_hcd and address 5
[ 2411.930769] usb 1-2: configuration #1 chosen from 1 choice
[ 2411.933804] scsi7 : SCSI emulation for USB Mass Storage devices
[ 2411.934040] usb-storage: device found at 5
[ 2411.934044] usb-storage: waiting for device to settle before scanning
[ 2416.935627] usb-storage: device scan complete
[ 2416.938623] scsi 7:0:0:0: Direct-Access TwinMOS MOBILE Disk 1.11 PQ: 0 ANSI: 2
[ 2416.944133] SCSI device sdf: 516096 512-byte hdwr sectors (264 MB)
[ 2416.946600] sdf: Write Protect is off
[ 2416.946605] sdf: Mode Sense: 03 00 00 00
[ 2416.946609] sdf: assuming drive cache: write through
[ 2416.958590] SCSI device sdf: 516096 512-byte hdwr sectors (264 MB)
[ 2416.961588] sdf: Write Protect is off
[ 2416.961592] sdf: Mode Sense: 03 00 00 00
[ 2416.961619] sdf: assuming drive cache: write through
[ 2416.961624] sdf: unknown partition table
[ 2416.979703] sd 7:0:0:0: Attached scsi removable disk sdf
[ 2416.979773] sd 7:0:0:0: Attached scsi generic sg6 type 0
[15418.271640] SCSI device sde: 59776 512-byte hdwr sectors (31 MB)
[15418.272890] sde: Write Protect is off
[15418.272894] sde: Mode Sense: 03 00 00 00
[15418.272899] sde: assuming drive cache: write through
[15418.274635] SCSI device sde: 59776 512-byte hdwr sectors (31 MB)
[15418.275887] sde: Write Protect is off
[15418.275891] sde: Mode Sense: 03 00 00 00
[15418.275895] sde: assuming drive cache: write through
[15418.275899] sde: unknown partition table
[15563.933358] usb 1-2: USB disconnect, address 5
[15563.935930] VFS: busy inodes on changed media.
[15563.937506] scsi 7:0:0:0: rejecting I/O to dead device
[15563.937521] scsi 7:0:0:0: rejecting I/O to dead device
[15563.937528] scsi 7:0:0:0: rejecting I/O to dead device
[15563.937535] sdf : READ CAPACITY failed.
[15563.937537] sdf : status=0, message=00, host=1, driver=00
[15563.937541] sdf : sense not available.
[15563.937547] scsi 7:0:0:0: rejecting I/O to dead device
[15563.937553] sdf: Write Protect is off
[15563.937557] sdf: Mode Sense: 00 00 00 00
[15563.937560] sdf: assuming drive cache: write through
[24901.424647] usb 5-7: new high speed USB device using ehci_hcd and address 7
[24901.564644] usb 5-7: configuration #1 chosen from 1 choice
[24908.255514] usb 5-7: USB disconnect, address 7
[24917.817890] usb 5-7: new high speed USB device using ehci_hcd and address 8
[24917.957905] usb 5-7: configuration #1 chosen from 1 choice
[24923.372979] usb 5-7: USB disconnect, address 8
[24932.935350] usb 5-7: new high speed USB device using ehci_hcd and address 9
[24933.075367] usb 5-7: configuration #1 chosen from 1 choice
[24938.490437] usb 5-7: USB disconnect, address 9
[24948.052808] usb 5-7: new high speed USB device using ehci_hcd and address 10
[24948.192847] usb 5-7: configuration #1 chosen from 1 choice
[24953.607899] usb 5-7: USB disconnect, address 10
[24963.170291] usb 5-7: new high speed USB device using ehci_hcd and address 11
[24963.310259] usb 5-7: configuration #1 chosen from 1 choice
[24968.993310] usb 5-7: USB disconnect, address 11
[24978.559688] usb 5-7: new high speed USB device using ehci_hcd and address 12
[24978.707661] usb 5-7: configuration #1 chosen from 1 choice
[24984.614694] usb 5-7: USB disconnect, address 12
[24994.433034] usb 5-7: new high speed USB device using ehci_hcd and address 13
[24994.569032] usb 5-7: configuration #1 chosen from 1 choice
[24999.988106] usb 5-7: USB disconnect, address 13
[25009.550484] usb 5-7: new high speed USB device using ehci_hcd and address 14
[25009.686572] usb 5-7: configuration #1 chosen from 1 choice
[25015.105569] usb 5-7: USB disconnect, address 14
[25024.667942] usb 5-7: new high speed USB device using ehci_hcd and address 15
[25024.803973] usb 5-7: configuration #1 chosen from 1 choice
[25030.239021] usb 5-7: USB disconnect, address 15
[25040.053362] usb 5-7: new high speed USB device using ehci_hcd and address 16
[25040.193369] usb 5-7: configuration #1 chosen from 1 choice
[25045.608439] usb 5-7: USB disconnect, address 16
[25055.170816] usb 5-7: new high speed USB device using ehci_hcd and address 17
[25055.310773] usb 5-7: configuration #1 chosen from 1 choice
[25060.741899] usb 5-7: USB disconnect, address 17
[25070.556231] usb 5-7: new high speed USB device using ehci_hcd and address 18
[25070.696210] usb 5-7: configuration #1 chosen from 1 choice
[25076.127324] usb 5-7: USB disconnect, address 18
[25085.689700] usb 5-7: new high speed USB device using ehci_hcd and address 19
[25085.829721] usb 5-7: configuration #1 chosen from 1 choice
[25091.260767] usb 5-7: USB disconnect, address 19
[25100.823154] usb 5-7: new high speed USB device using ehci_hcd and address 20
[25100.963123] usb 5-7: configuration #1 chosen from 1 choice
[25106.394237] usb 5-7: USB disconnect, address 20
[25115.956605] usb 5-7: new high speed USB device using ehci_hcd and address 21
[25116.096648] usb 5-7: configuration #1 chosen from 1 choice
[25121.527684] usb 5-7: USB disconnect, address 21
[25131.090062] usb 5-7: new high speed USB device using ehci_hcd and address 22
[25131.230055] usb 5-7: configuration #1 chosen from 1 choice
[25136.645144] usb 5-7: USB disconnect, address 22
[25146.459481] usb 5-7: new high speed USB device using ehci_hcd and address 23
[25146.599485] usb 5-7: configuration #1 chosen from 1 choice
[25152.030560] usb 5-7: USB disconnect, address 23
[25161.592938] usb 5-7: new high speed USB device using ehci_hcd and address 24
[25161.732871] usb 5-7: configuration #1 chosen from 1 choice
[25167.164017] usb 5-7: USB disconnect, address 24
[25176.726395] usb 5-7: new high speed USB device using ehci_hcd and address 25
[25176.866409] usb 5-7: configuration #1 chosen from 1 choice
[25182.297476] usb 5-7: USB disconnect, address 25
[25191.863865] usb 5-7: new high speed USB device using ehci_hcd and address 26
[25192.011789] usb 5-7: configuration #1 chosen from 1 choice
[25197.434943] usb 5-7: USB disconnect, address 26
[25206.997311] usb 5-7: new high speed USB device using ehci_hcd and address 27
[25207.133334] usb 5-7: configuration #1 chosen from 1 choice
[25212.568389] usb 5-7: USB disconnect, address 27
[25222.382726] usb 5-7: new high speed USB device using ehci_hcd and address 28
[25222.518761] usb 5-7: configuration #1 chosen from 1 choice
[25227.937809] usb 5-7: USB disconnect, address 28
[25237.500184] usb 5-7: new high speed USB device using ehci_hcd and address 29
[25237.636143] usb 5-7: configuration #1 chosen from 1 choice
[25243.055268] usb 5-7: USB disconnect, address 29
[25252.617662] usb 5-7: new high speed USB device using ehci_hcd and address 30
[25252.757718] usb 5-7: configuration #1 chosen from 1 choice
[25258.188754] usb 5-7: USB disconnect, address 30
[25267.751110] usb 5-7: new high speed USB device using ehci_hcd and address 31
[25267.891087] usb 5-7: configuration #1 chosen from 1 choice
[25273.322190] usb 5-7: USB disconnect, address 31
[25282.884565] usb 5-7: new high speed USB device using ehci_hcd and address 32
[25283.024676] usb 5-7: configuration #1 chosen from 1 choice
[25288.439648] usb 5-7: USB disconnect, address 32
[25298.253984] usb 5-7: new high speed USB device using ehci_hcd and address 33
[25298.394040] usb 5-7: configuration #1 chosen from 1 choice
[25303.825069] usb 5-7: USB disconnect, address 33
[25313.387441] usb 5-7: new high speed USB device using ehci_hcd and address 34
[25313.527440] usb 5-7: configuration #1 chosen from 1 choice
[25318.958527] usb 5-7: USB disconnect, address 34
[25328.520894] usb 5-7: new high speed USB device using ehci_hcd and address 35
[25328.660831] usb 5-7: configuration #1 chosen from 1 choice
[25334.091975] usb 5-7: USB disconnect, address 35
[25343.906373] usb 5-7: new high speed USB device using ehci_hcd and address 36
[25344.046251] usb 5-7: configuration #1 chosen from 1 choice
[25349.729344] usb 5-7: USB disconnect, address 36
[25359.543684] usb 5-7: new high speed USB device using ehci_hcd and address 37
[25359.683710] usb 5-7: configuration #1 chosen from 1 choice
[25365.098764] usb 5-7: USB disconnect, address 37
[25374.913101] usb 5-7: new high speed USB device using ehci_hcd and address 38
[25375.053132] usb 5-7: configuration #1 chosen from 1 choice
[25380.468183] usb 5-7: USB disconnect, address 38
[25390.282521] usb 5-7: new high speed USB device using ehci_hcd and address 39
[25390.422549] usb 5-7: configuration #1 chosen from 1 choice
[25395.853602] usb 5-7: USB disconnect, address 39
[25405.423975] usb 5-7: new high speed USB device using ehci_hcd and address 40
[25405.571955] usb 5-7: configuration #1 chosen from 1 choice
[25411.243022] usb 5-7: USB disconnect, address 40
[25420.805400] usb 5-7: new high speed USB device using ehci_hcd and address 41
[25420.941396] usb 5-7: configuration #1 chosen from 1 choice
[25426.360472] usb 5-7: USB disconnect, address 41
[25435.922853] usb 5-7: new high speed USB device using ehci_hcd and address 42
[25436.058927] usb 5-7: configuration #1 chosen from 1 choice
[25441.493935] usb 5-7: USB disconnect, address 42
[25451.056315] usb 5-7: new high speed USB device using ehci_hcd and address 43
[25451.196315] usb 5-7: configuration #1 chosen from 1 choice
[25456.627395] usb 5-7: USB disconnect, address 43
[25466.189770] usb 5-7: new high speed USB device using ehci_hcd and address 44
[25466.329700] usb 5-7: configuration #1 chosen from 1 choice
[25471.744853] usb 5-7: USB disconnect, address 44
[25481.559201] usb 5-7: new high speed USB device using ehci_hcd and address 45
[25481.699140] usb 5-7: configuration #1 chosen from 1 choice
[25487.382225] usb 5-7: USB disconnect, address 45
[25496.944604] usb 5-7: new high speed USB device using ehci_hcd and address 46
[25497.084557] usb 5-7: configuration #1 chosen from 1 choice
[25502.499681] usb 5-7: USB disconnect, address 46
[25512.314016] usb 5-7: new high speed USB device using ehci_hcd and address 47
[25512.453975] usb 5-7: configuration #1 chosen from 1 choice
[25517.869099] usb 5-7: USB disconnect, address 47
[25527.431479] usb 5-7: new high speed USB device using ehci_hcd and address 48
[25527.571518] usb 5-7: configuration #1 chosen from 1 choice
[25533.002568] usb 5-7: USB disconnect, address 48
[25542.564958] usb 5-7: new high speed USB device using ehci_hcd and address 49
[25542.704941] usb 5-7: configuration #1 chosen from 1 choice
[25548.387975] usb 5-7: USB disconnect, address 49
[25557.950349] usb 5-7: new high speed USB device using ehci_hcd and address 50
[25558.090331] usb 5-7: configuration #1 chosen from 1 choice
[25563.773390] usb 5-7: USB disconnect, address 50
[25573.335765] usb 5-7: new high speed USB device using ehci_hcd and address 51
[25573.475757] usb 5-7: configuration #1 chosen from 1 choice
[25578.906851] usb 5-7: USB disconnect, address 51
[25588.469222] usb 5-7: new high speed USB device using ehci_hcd and address 52
[25588.609149] usb 5-7: configuration #1 chosen from 1 choice
[25594.024307] usb 5-7: USB disconnect, address 52
[25603.586684] usb 5-7: new high speed USB device using ehci_hcd and address 53
[25603.726685] usb 5-7: configuration #1 chosen from 1 choice
[25609.141768] usb 5-7: USB disconnect, address 53
[25618.708141] usb 5-7: new high speed USB device using ehci_hcd and address 54
[25618.844095] usb 5-7: configuration #1 chosen from 1 choice
[25624.279226] usb 5-7: USB disconnect, address 54
[25633.841606] usb 5-7: new high speed USB device using ehci_hcd and address 55
[25633.977625] usb 5-7: configuration #1 chosen from 1 choice
[25639.412691] usb 5-7: USB disconnect, address 55
[25649.227017] usb 5-7: new high speed USB device using ehci_hcd and address 56
[25649.363046] usb 5-7: configuration #1 chosen from 1 choice
[25654.798098] usb 5-7: USB disconnect, address 56