Hi,
feisty on laptop Packard Bell Easynote R1983.
My wireless card is not recognized, unless I put the option "acpi=force" to kernel. But this disables all my usb devices. If I reboot without "acpi=force" to kernel, then usb works fine, but no wireless card recognized!
Help!
Bob in Florence
With "acpi=force":
Here are some bunch (sorry, pastebin not working today):
$ lspci -v: (extract)
00:06.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Askey Computer Corp. Unknown device 7084
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at 20000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
$ dmesg (with acpi=force):
[ 0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (
Ubuntu 2.6.20-15.27-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
...
...
[ 0.000000] ACPI: RSDP (v000 OID_00 ) @ 0x000e6010
[ 0.000000] ACPI: RSDT (v001 INSYDE FACP_000 0x00000100 0000 0x00010200) @ 0x1bffc2d0
[ 0.000000] ACPI: FADT (v001 INSYDE FACP_000 0x00000100 0000 0x00010200) @ 0x1bfffb00
[ 0.000000] ACPI: MADT (v001 INSYDE APIC_000 0x30303030 0000 0x00010200) @ 0x1bfffb90
[ 0.000000] ACPI: DSDT (v001 INSYDE PN800 0x00001000 INTL 0x02002036) @ 0x00000000
[ 0.000000] ACPI: BIOS age (400) fails cutoff (2000), acpi=force is required to enable ACPI
[ 0.000000] ACPI: acpi=force override
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
...
[ 14.296460] ACPI: bus type pci registered
[ 14.296511] PCI: PCI BIOS revision 2.10 entry at 0xe9b04, last bus=1
[ 14.296513] PCI: Using configuration type 1
[ 14.296515] Setting up standard PCI resources
[ 14.300503] ACPI: Interpreter enabled
[ 14.300507] ACPI: Using IOAPIC for interrupt routing
[ 14.301191] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 14.301201] PCI: Probing PCI hardware (bus 00)
[ 14.301304] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 14.302185] PCI quirk: region 1000-107f claimed by vt8235 PM
[ 14.302190] PCI quirk: region 1400-140f claimed by vt8235 SMB
[ 14.302484] Boot video device is 0000:01:00.0
[ 14.302544] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 14.318529] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 14.318777] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 *7 10 11 14 15)
[ 14.319026] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 14.319271] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 14 15)
[ 14.319505] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.319734] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.319977] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.320211] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.320437] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
[ 14.320708] ACPI: PCI Interrupt Link [ALKB] (IRQs 23) *11
[ 14.321027] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *5, disabled.
[ 14.321219] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 14.321229] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 14.321236] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 14.321240] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *0
[ 14.321365] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.321382] pnp: PnP ACPI init
[ 14.325661] pnp: PnP ACPI: found 9 devices
[ 14.325669] PnPBIOS: Disabled by ACPI PNP
[ 14.325731] PCI: Using ACPI for IRQ routing
[ 14.325735] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 14.328051] NET: Registered protocol family 8
[ 14.328054] NET: Registered protocol family 20
[ 14.328211] pnp: 00:07: ioport range 0x330-0x331 has been reserved
[ 14.328215] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 14.328218] pnp: 00:07: ioport range 0x1000-0x107f could not be reserved
[ 14.328222] pnp: 00:07: ioport range 0x1400-0x140f has been reserved
[ 14.328549] PCI: Bridge: 0000:00:01.0
[ 14.328553] IO window: c000-dfff
[ 14.328559] MEM window: c0000000-cfffffff
[ 14.328564] PREFETCH window: 90000000-9fffffff
[ 14.328587] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 14.328620] NET: Registered protocol family 2
[ 14.355817] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 14.355911] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 14.356066] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 14.356132] TCP: Hash tables configured (established 16384 bind 8192)
[ 14.356135] TCP reno registered
[ 14.367870] checking if image is initramfs... it is
[ 15.126120] Freeing initrd memory: 7007k freed
[ 15.126767] audit: initializing netlink socket (disabled)
[ 15.126788] audit(1178618720.560:1): initialized
[ 15.126965] VFS: Disk quotas dquot_6.5.1
[ 15.126993] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 15.127060] io scheduler noop registered
[ 15.127064] io scheduler anticipatory registered
[ 15.127066] io scheduler deadline registered
[ 15.127079] io scheduler cfq registered (default)
[ 15.127435] isapnp: Scanning for PnP cards...
[ 15.481381] isapnp: No Plug & Play device found
[ 15.520684] Real Time Clock Driver v1.12ac
[ 15.520754] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 15.521786] mice: PS/2 mouse device common for all mice
[ 15.522497] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 15.522812] input: Macintosh mouse button emulation as /class/input/input0
[ 15.522850] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 15.522855] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 15.523151] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 15.533458] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 15.538438] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 15.538444] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 15.538447] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 15.538449] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 15.538452] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 15.539019] EISA: Probing bus 0 at eisa.0
[ 15.539029] Cannot allocate resource for EISA slot 1
[ 15.539063] EISA: Detected 0 cards.
[ 15.569149] TCP cubic registered
[ 15.569162] NET: Registered protocol family 1
[ 15.569189] Using IPI No-Shortcut mode
[ 15.569279] ACPI: (supports S0 S1 S3 S4 S5)
[ 15.569335] Magic number: 7:166:72
[ 15.569826] Freeing unused kernel memory: 328k freed
[ 15.569992] Time: tsc clocksource has been installed.
[ 15.574391] input: AT Translated Set 2 keyboard as /class/input/input1
[ 16.800063] Capability LSM initialized
[ 16.834906] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 16.834914] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 16.841613] ACPI: Thermal Zone [TZ0] (0 C)
[ 17.300199] usbcore: registered new interface driver usbfs
[ 17.300227] usbcore: registered new interface driver hub
[ 17.300250] usbcore: registered new device driver usb
[ 17.301244] USB Universal Host Controller Interface driver v3.0
[ 17.301473] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 17.301484] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 17.301491] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 17.301496] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 17.301501] ACPI: Invalid IRQ link routing entry
[ 17.301503] ACPI: Unable to derive IRQ for device 0000:00:10.0
[ 17.301506] ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI - using IRQ 11
[ 17.301534] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 17.301743] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 17.301781] uhci_hcd 0000:00:10.0: irq 11, io base 0x00001200
[ 17.301900] usb usb1: configuration #1 chosen from 1 choice
[ 17.301932] hub 1-0:1.0: USB hub found
[ 17.301938] hub 1-0:1.0: 2 ports detected
[ 17.375089] via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
[ 17.403725] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 17.403738] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 17.403746] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 17.403750] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 17.403756] ACPI: Invalid IRQ link routing entry
[ 17.403758] ACPI: Unable to derive IRQ for device 0000:00:10.1
[ 17.403760] ACPI: PCI Interrupt 0000:00:10.1[B]: no GSI - using IRQ 7
[ 17.403790] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 17.403824] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 17.403863] uhci_hcd 0000:00:10.1: irq 7, io base 0x00001220
[ 17.403970] usb usb2: configuration #1 chosen from 1 choice
[ 17.404000] hub 2-0:1.0: USB hub found
[ 17.404008] hub 2-0:1.0: 2 ports detected
[ 17.507597] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 17.507609] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 17.507617] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 17.507621] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 17.507626] ACPI: Invalid IRQ link routing entry
[ 17.507629] ACPI: Unable to derive IRQ for device 0000:00:10.2
[ 17.507631] ACPI: PCI Interrupt 0000:00:10.2[C]: no GSI - using IRQ 5
[ 17.507661] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 17.507692] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 17.507731] uhci_hcd 0000:00:10.2: irq 5, io base 0x00001240
[ 17.507849] usb usb3: configuration #1 chosen from 1 choice
[ 17.507878] hub 3-0:1.0: USB hub found
[ 17.507885] hub 3-0:1.0: 2 ports detected
[ 3.804000] Time: acpi_pm clocksource has been installed.
[ 3.860000] PCI: Enabling device 0000:00:10.3 (0000 -> 0002)
[ 3.860000] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 3.860000] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 3.860000] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 3.860000] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 3.860000] ACPI: Invalid IRQ link routing entry
[ 3.860000] ACPI: Unable to derive IRQ for device 0000:00:10.3
[ 3.860000] ACPI: PCI Interrupt 0000:00:10.3[D]: no GSI - using IRQ 10
[ 3.860000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 3.860000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 3.860000] ehci_hcd 0000:00:10.3: irq 10, io mem 0x20010000
[ 3.860000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.860000] usb usb4: configuration #1 chosen from 1 choice
[ 3.860000] hub 4-0:1.0: USB hub found
[ 3.860000] hub 4-0:1.0: 6 ports detected
[ 3.964000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[ 3.964000] ACPI: PCI Interrupt Link [ALKA] disabled and referenced, BIOS bug
[ 3.964000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[ 3.964000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 3.964000] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 16
[ 3.964000] VP_IDE: chipset revision 6
[ 3.964000] VP_IDE: not 100% native mode: will probe irqs later
[ 3.964000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
[ 3.964000] ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda
MA, hdb
io
[ 3.964000] ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdcMA, hddio
[ 3.964000] Probing IDE interface ide0...
[ 4.380000] hda: WDC WD800UE-22HCT0, ATA DISK drive
[ 5.004000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 5.052000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.096000] Probing IDE interface ide1...
[ 5.960000] hdc: , ATAPI cdrom or floppy?, assuming FLOPPY drive
[ 6.632000] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.640000] SCSI subsystem initialized
[ 6.648000] libata version 2.20 loaded.
[ 6.652000] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 11, using IRQ 23
[ 6.652000] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 23
[ 6.652000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKB] -> GSI 23 (level, low) -> IRQ 17
[ 6.656000] eth0: VIA Rhine II at 0x1e200, 00:40:d0:8c:b7:37, IRQ 17.
[ 6.656000] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 6.664000] hda: max request size: 128KiB
[ 6.664000] hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 6.668000] ide-floppy driver 0.99.newide
[ 6.672000] hda: cache flushes supported
...
[ 9.300000] usb 2-1: configuration #1 chosen from 1 choice
[ 17.924000] eth0: link down
[ 19.200000] NET: Registered protocol family 17
[ 19.572000] ath_hal: module license 'Proprietary' taints kernel.
[ 19.576000] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 20.576000] wlan: 0.8.4.2 (0.9.3)
[ 20.728000] Linux agpgart interface v0.102 (c) Dave Jones
[ 20.748000] input: PC Speaker as /class/input/input2
[ 20.772000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 20.772000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 20.824000] irda_init()
[ 20.824000] NET: Registered protocol family 23
[ 20.852000] agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset
[ 20.856000] agpgart: AGP aperture is 32M @ 0xa0000000
[ 20.904000] ath_pci: 0.9.4.5 (0.9.3)
[ 20.904000] PCI: Enabling device 0000:00:06.0 (0000 -> 0002)
[ 20.904000] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 19 (level, low) -> IRQ 18
[ 21.636000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0xf6eb3, caps: 0xa04713/0x0
[ 21.692000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[ 21.876000] ath_rate_sample: 1.2 (0.9.3)
[ 21.876000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 21.876000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 21.876000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 21.876000] wifi0: mac 7.8 phy 4.5 radio 5.6
[ 21.876000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 21.876000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 21.876000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 21.876000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 21.876000] wifi0: Use hw queue 8 for CAB traffic
[ 21.876000] wifi0: Use hw queue 9 for beacons
[ 21.904000] wifi0: Atheros 5212: mem=0x20000000, irq=18
[ 22.264000] ACPI: PCI Interrupt Link [ALKC] disabled and referenced, BIOS bug
[ 22.264000] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 5, using IRQ 22
[ 22.264000] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 22.264000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 19
[ 22.264000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 23.112000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x4C11
[ 23.112000] usbcore: registered new interface driver usblp
[ 23.112000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 23.348000] fuse init (API version 7.8)
[ 23.420000] lp: driver loaded but no devices found
[ 23.448000] Adding 1020088k swap on /dev/disk/by-uuid/36e9fbed-1278-4dd8-901f-9a14b01a7e12. Priority:-1 extents:1 across:1020088k
[ 23.708000] EXT3 FS on hda6, internal journal
...
[ 31.012000] ACPI: AC Adapter [AC] (on-line)
[ 31.068000] ACPI: Battery Slot [BAT0] (battery present)
[ 31.096000] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 31.184000] ibm_acpi: ec object not found
[ 31.320000] input: Power Button (FF) as /class/input/input4
[ 31.328000] ACPI: Power Button (FF) [PWRF]
[ 31.376000] input: Lid Switch as /class/input/input5
[ 31.380000] ACPI: Lid Switch [LID]
[ 31.428000] input: Sleep Button (CM) as /class/input/input6
[ 31.432000] ACPI: Sleep Button (CM) [SBTN]
[ 31.464000] pcc_acpi: loading...
[ 36.288000] ppdev: user-space parallel port driver
[ 37.516000] apm: BIOS not found.
[ 38.132000] Bluetooth: Core ver 2.11
...
[ 40.080000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 40.080000] [drm] Initialized via 2.11.0 20061227 on minor 0
[ 40.144000] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 40.144000] agpgart: Device is in legacy mode, falling back to 2.x
[ 40.148000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 40.148000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 40.152000] [drm:via_mem_alloc] *ERROR* Attempt to allocate from uninitialized memory manager.
[ 89.688000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 107.292000] ath0: no IPv6 routers present
[ 3299.112000] usb 2-1: USB disconnect, address 2
[ 3299.212000] drivers/usb/class/usblp.c: usblp0: removed
...
feisty on laptop Packard Bell Easynote R1983.
My wireless card is not recognized, unless I put the option "acpi=force" to kernel. But this disables all my usb devices. If I reboot without "acpi=force" to kernel, then usb works fine, but no wireless card recognized!
Help!
Bob in Florence
With "acpi=force":
Here are some bunch (sorry, pastebin not working today):
$ lspci -v: (extract)
00:06.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01)
Subsystem: Askey Computer Corp. Unknown device 7084
Flags: bus master, medium devsel, latency 168, IRQ 18
Memory at 20000000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [44] Power Management version 2
$ dmesg (with acpi=force):
[ 0.000000] Linux version 2.6.20-15-generic (root@palmer) (gcc version 4.1.2 (Ubuntu 4.1.2-0ubuntu4)) #2 SMP Sun Apr 15 07:36:31 UTC 2007 (
Ubuntu 2.6.20-15.27-generic)
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] sanitize start
[ 0.000000] sanitize end
[ 0.000000] copy_e820_map() start: 0000000000000000 size: 000000000009fc00 end: 000000000009fc00 type: 1
...
...
[ 0.000000] ACPI: RSDP (v000 OID_00 ) @ 0x000e6010
[ 0.000000] ACPI: RSDT (v001 INSYDE FACP_000 0x00000100 0000 0x00010200) @ 0x1bffc2d0
[ 0.000000] ACPI: FADT (v001 INSYDE FACP_000 0x00000100 0000 0x00010200) @ 0x1bfffb00
[ 0.000000] ACPI: MADT (v001 INSYDE APIC_000 0x30303030 0000 0x00010200) @ 0x1bfffb90
[ 0.000000] ACPI: DSDT (v001 INSYDE PN800 0x00001000 INTL 0x02002036) @ 0x00000000
[ 0.000000] ACPI: BIOS age (400) fails cutoff (2000), acpi=force is required to enable ACPI
[ 0.000000] ACPI: acpi=force override
[ 0.000000] ACPI: PM-Timer IO Port: 0x1008
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 6:13 APIC version 20
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
...
[ 14.296460] ACPI: bus type pci registered
[ 14.296511] PCI: PCI BIOS revision 2.10 entry at 0xe9b04, last bus=1
[ 14.296513] PCI: Using configuration type 1
[ 14.296515] Setting up standard PCI resources
[ 14.300503] ACPI: Interpreter enabled
[ 14.300507] ACPI: Using IOAPIC for interrupt routing
[ 14.301191] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 14.301201] PCI: Probing PCI hardware (bus 00)
[ 14.301304] ACPI: Assume root bridge [\_SB_.PCI0] bus is 0
[ 14.302185] PCI quirk: region 1000-107f claimed by vt8235 PM
[ 14.302190] PCI quirk: region 1400-140f claimed by vt8235 SMB
[ 14.302484] Boot video device is 0000:01:00.0
[ 14.302544] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 14.318529] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 10 *11 14 15)
[ 14.318777] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 *7 10 11 14 15)
[ 14.319026] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 10 11 14 15)
[ 14.319271] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 14 15)
[ 14.319505] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.319734] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.319977] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.320211] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 14 15) *0, disabled.
[ 14.320437] ACPI: PCI Interrupt Link [ALKA] (IRQs 20) *0, disabled.
[ 14.320708] ACPI: PCI Interrupt Link [ALKB] (IRQs 23) *11
[ 14.321027] ACPI: PCI Interrupt Link [ALKC] (IRQs 22) *5, disabled.
[ 14.321219] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 14.321229] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 14.321236] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 14.321240] ACPI: PCI Interrupt Link [ALKD] (IRQs 21) *0
[ 14.321365] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 14.321382] pnp: PnP ACPI init
[ 14.325661] pnp: PnP ACPI: found 9 devices
[ 14.325669] PnPBIOS: Disabled by ACPI PNP
[ 14.325731] PCI: Using ACPI for IRQ routing
[ 14.325735] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 14.328051] NET: Registered protocol family 8
[ 14.328054] NET: Registered protocol family 20
[ 14.328211] pnp: 00:07: ioport range 0x330-0x331 has been reserved
[ 14.328215] pnp: 00:07: ioport range 0x4d0-0x4d1 has been reserved
[ 14.328218] pnp: 00:07: ioport range 0x1000-0x107f could not be reserved
[ 14.328222] pnp: 00:07: ioport range 0x1400-0x140f has been reserved
[ 14.328549] PCI: Bridge: 0000:00:01.0
[ 14.328553] IO window: c000-dfff
[ 14.328559] MEM window: c0000000-cfffffff
[ 14.328564] PREFETCH window: 90000000-9fffffff
[ 14.328587] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 14.328620] NET: Registered protocol family 2
[ 14.355817] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 14.355911] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 14.356066] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
[ 14.356132] TCP: Hash tables configured (established 16384 bind 8192)
[ 14.356135] TCP reno registered
[ 14.367870] checking if image is initramfs... it is
[ 15.126120] Freeing initrd memory: 7007k freed
[ 15.126767] audit: initializing netlink socket (disabled)
[ 15.126788] audit(1178618720.560:1): initialized
[ 15.126965] VFS: Disk quotas dquot_6.5.1
[ 15.126993] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 15.127060] io scheduler noop registered
[ 15.127064] io scheduler anticipatory registered
[ 15.127066] io scheduler deadline registered
[ 15.127079] io scheduler cfq registered (default)
[ 15.127435] isapnp: Scanning for PnP cards...
[ 15.481381] isapnp: No Plug & Play device found
[ 15.520684] Real Time Clock Driver v1.12ac
[ 15.520754] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
[ 15.521786] mice: PS/2 mouse device common for all mice
[ 15.522497] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
[ 15.522812] input: Macintosh mouse button emulation as /class/input/input0
[ 15.522850] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
[ 15.522855] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
[ 15.523151] PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
[ 15.533458] i8042.c: Detected active multiplexing controller, rev 1.1.
[ 15.538438] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 15.538444] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 15.538447] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 15.538449] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 15.538452] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 15.539019] EISA: Probing bus 0 at eisa.0
[ 15.539029] Cannot allocate resource for EISA slot 1
[ 15.539063] EISA: Detected 0 cards.
[ 15.569149] TCP cubic registered
[ 15.569162] NET: Registered protocol family 1
[ 15.569189] Using IPI No-Shortcut mode
[ 15.569279] ACPI: (supports S0 S1 S3 S4 S5)
[ 15.569335] Magic number: 7:166:72
[ 15.569826] Freeing unused kernel memory: 328k freed
[ 15.569992] Time: tsc clocksource has been installed.
[ 15.574391] input: AT Translated Set 2 keyboard as /class/input/input1
[ 16.800063] Capability LSM initialized
[ 16.834906] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 16.834914] ACPI: Processor [CPU0] (supports 16 throttling states)
[ 16.841613] ACPI: Thermal Zone [TZ0] (0 C)
[ 17.300199] usbcore: registered new interface driver usbfs
[ 17.300227] usbcore: registered new interface driver hub
[ 17.300250] usbcore: registered new device driver usb
[ 17.301244] USB Universal Host Controller Interface driver v3.0
[ 17.301473] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 17.301484] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 17.301491] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 17.301496] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 17.301501] ACPI: Invalid IRQ link routing entry
[ 17.301503] ACPI: Unable to derive IRQ for device 0000:00:10.0
[ 17.301506] ACPI: PCI Interrupt 0000:00:10.0[A]: no GSI - using IRQ 11
[ 17.301534] uhci_hcd 0000:00:10.0: UHCI Host Controller
[ 17.301743] uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
[ 17.301781] uhci_hcd 0000:00:10.0: irq 11, io base 0x00001200
[ 17.301900] usb usb1: configuration #1 chosen from 1 choice
[ 17.301932] hub 1-0:1.0: USB hub found
[ 17.301938] hub 1-0:1.0: 2 ports detected
[ 17.375089] via-rhine.c:v1.10-LK1.4.2 Sept-11-2006 Written by Donald Becker
[ 17.403725] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 17.403738] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 17.403746] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 17.403750] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 17.403756] ACPI: Invalid IRQ link routing entry
[ 17.403758] ACPI: Unable to derive IRQ for device 0000:00:10.1
[ 17.403760] ACPI: PCI Interrupt 0000:00:10.1[B]: no GSI - using IRQ 7
[ 17.403790] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 17.403824] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
[ 17.403863] uhci_hcd 0000:00:10.1: irq 7, io base 0x00001220
[ 17.403970] usb usb2: configuration #1 chosen from 1 choice
[ 17.404000] hub 2-0:1.0: USB hub found
[ 17.404008] hub 2-0:1.0: 2 ports detected
[ 17.507597] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 17.507609] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 17.507617] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 17.507621] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 17.507626] ACPI: Invalid IRQ link routing entry
[ 17.507629] ACPI: Unable to derive IRQ for device 0000:00:10.2
[ 17.507631] ACPI: PCI Interrupt 0000:00:10.2[C]: no GSI - using IRQ 5
[ 17.507661] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 17.507692] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
[ 17.507731] uhci_hcd 0000:00:10.2: irq 5, io base 0x00001240
[ 17.507849] usb usb3: configuration #1 chosen from 1 choice
[ 17.507878] hub 3-0:1.0: USB hub found
[ 17.507885] hub 3-0:1.0: 2 ports detected
[ 3.804000] Time: acpi_pm clocksource has been installed.
[ 3.860000] PCI: Enabling device 0000:00:10.3 (0000 -> 0002)
[ 3.860000] ACPI Error (uteval-0269): Return object type is incorrect [\_SB_.PCI0.ALKD._CRS] (Node da7319f0), AE_TYPE
[ 3.860000] ACPI Error (uteval-0275): Type returned from _CRS was incorrect: Integer, expected Btypes: 4 [20060707]
[ 3.860000] ACPI Exception (pci_link-0278): AE_TYPE, Evaluating _CRS [20060707]
[ 3.860000] ACPI: Unable to set IRQ for PCI Interrupt Link [ALKD]. Try pci=noacpi or acpi=off
[ 3.860000] ACPI: Invalid IRQ link routing entry
[ 3.860000] ACPI: Unable to derive IRQ for device 0000:00:10.3
[ 3.860000] ACPI: PCI Interrupt 0000:00:10.3[D]: no GSI - using IRQ 10
[ 3.860000] ehci_hcd 0000:00:10.3: EHCI Host Controller
[ 3.860000] ehci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
[ 3.860000] ehci_hcd 0000:00:10.3: irq 10, io mem 0x20010000
[ 3.860000] ehci_hcd 0000:00:10.3: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 3.860000] usb usb4: configuration #1 chosen from 1 choice
[ 3.860000] hub 4-0:1.0: USB hub found
[ 3.860000] hub 4-0:1.0: 6 ports detected
[ 3.964000] VP_IDE: IDE controller at PCI slot 0000:00:11.1
[ 3.964000] ACPI: PCI Interrupt Link [ALKA] disabled and referenced, BIOS bug
[ 3.964000] ACPI: PCI Interrupt Link [ALKA] BIOS reported IRQ 0, using IRQ 20
[ 3.964000] ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
[ 3.964000] ACPI: PCI Interrupt 0000:00:11.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 16
[ 3.964000] VP_IDE: chipset revision 6
[ 3.964000] VP_IDE: not 100% native mode: will probe irqs later
[ 3.964000] VP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci0000:00:11.1
[ 3.964000] ide0: BM-DMA at 0x1100-0x1107, BIOS settings: hda
MA, hdbio[ 3.964000] ide1: BM-DMA at 0x1108-0x110f, BIOS settings: hdc
MA, hddio[ 3.964000] Probing IDE interface ide0...
[ 4.380000] hda: WDC WD800UE-22HCT0, ATA DISK drive
[ 5.004000] usb 2-1: new full speed USB device using uhci_hcd and address 2
[ 5.052000] ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
[ 5.096000] Probing IDE interface ide1...
[ 5.960000] hdc: , ATAPI cdrom or floppy?, assuming FLOPPY drive
[ 6.632000] ide1 at 0x170-0x177,0x376 on irq 15
[ 6.640000] SCSI subsystem initialized
[ 6.648000] libata version 2.20 loaded.
[ 6.652000] ACPI: PCI Interrupt Link [ALKB] BIOS reported IRQ 11, using IRQ 23
[ 6.652000] ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 23
[ 6.652000] ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKB] -> GSI 23 (level, low) -> IRQ 17
[ 6.656000] eth0: VIA Rhine II at 0x1e200, 00:40:d0:8c:b7:37, IRQ 17.
[ 6.656000] eth0: MII PHY found at address 1, status 0x7849 advertising 05e1 Link 0000.
[ 6.664000] hda: max request size: 128KiB
[ 6.664000] hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
[ 6.668000] ide-floppy driver 0.99.newide
[ 6.672000] hda: cache flushes supported
...
[ 9.300000] usb 2-1: configuration #1 chosen from 1 choice
[ 17.924000] eth0: link down
[ 19.200000] NET: Registered protocol family 17
[ 19.572000] ath_hal: module license 'Proprietary' taints kernel.
[ 19.576000] ath_hal: 0.9.18.0 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
[ 20.576000] wlan: 0.8.4.2 (0.9.3)
[ 20.728000] Linux agpgart interface v0.102 (c) Dave Jones
[ 20.748000] input: PC Speaker as /class/input/input2
[ 20.772000] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 20.772000] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 20.824000] irda_init()
[ 20.824000] NET: Registered protocol family 23
[ 20.852000] agpgart: Detected VIA PM800/PN800/PM880/PN880 chipset
[ 20.856000] agpgart: AGP aperture is 32M @ 0xa0000000
[ 20.904000] ath_pci: 0.9.4.5 (0.9.3)
[ 20.904000] PCI: Enabling device 0000:00:06.0 (0000 -> 0002)
[ 20.904000] ACPI: PCI Interrupt 0000:00:06.0[A] -> GSI 19 (level, low) -> IRQ 18
[ 21.636000] Synaptics Touchpad, model: 1, fw: 5.9, id: 0xf6eb3, caps: 0xa04713/0x0
[ 21.692000] input: SynPS/2 Synaptics TouchPad as /class/input/input3
[ 21.876000] ath_rate_sample: 1.2 (0.9.3)
[ 21.876000] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 21.876000] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 21.876000] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 21.876000] wifi0: mac 7.8 phy 4.5 radio 5.6
[ 21.876000] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 21.876000] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 21.876000] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 21.876000] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 21.876000] wifi0: Use hw queue 8 for CAB traffic
[ 21.876000] wifi0: Use hw queue 9 for beacons
[ 21.904000] wifi0: Atheros 5212: mem=0x20000000, irq=18
[ 22.264000] ACPI: PCI Interrupt Link [ALKC] disabled and referenced, BIOS bug
[ 22.264000] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 5, using IRQ 22
[ 22.264000] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 22.264000] ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 19
[ 22.264000] PCI: Setting latency timer of device 0000:00:11.5 to 64
[ 23.112000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 2 if 1 alt 0 proto 2 vid 0x03F0 pid 0x4C11
[ 23.112000] usbcore: registered new interface driver usblp
[ 23.112000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
[ 23.348000] fuse init (API version 7.8)
[ 23.420000] lp: driver loaded but no devices found
[ 23.448000] Adding 1020088k swap on /dev/disk/by-uuid/36e9fbed-1278-4dd8-901f-9a14b01a7e12. Priority:-1 extents:1 across:1020088k
[ 23.708000] EXT3 FS on hda6, internal journal
...
[ 31.012000] ACPI: AC Adapter [AC] (on-line)
[ 31.068000] ACPI: Battery Slot [BAT0] (battery present)
[ 31.096000] ACPI: Video Device [VGA0] (multi-head: yes rom: no post: no)
[ 31.184000] ibm_acpi: ec object not found
[ 31.320000] input: Power Button (FF) as /class/input/input4
[ 31.328000] ACPI: Power Button (FF) [PWRF]
[ 31.376000] input: Lid Switch as /class/input/input5
[ 31.380000] ACPI: Lid Switch [LID]
[ 31.428000] input: Sleep Button (CM) as /class/input/input6
[ 31.432000] ACPI: Sleep Button (CM) [SBTN]
[ 31.464000] pcc_acpi: loading...
[ 36.288000] ppdev: user-space parallel port driver
[ 37.516000] apm: BIOS not found.
[ 38.132000] Bluetooth: Core ver 2.11
...
[ 40.080000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 20
[ 40.080000] [drm] Initialized via 2.11.0 20061227 on minor 0
[ 40.144000] agpgart: Found an AGP 3.5 compliant device at 0000:00:00.0.
[ 40.144000] agpgart: Device is in legacy mode, falling back to 2.x
[ 40.148000] agpgart: Putting AGP V2 device at 0000:00:00.0 into 0x mode
[ 40.148000] agpgart: Putting AGP V2 device at 0000:01:00.0 into 0x mode
[ 40.152000] [drm:via_mem_alloc] *ERROR* Attempt to allocate from uninitialized memory manager.
[ 89.688000] ADDRCONF(NETDEV_CHANGE): ath0: link becomes ready
[ 107.292000] ath0: no IPv6 routers present
[ 3299.112000] usb 2-1: USB disconnect, address 2
[ 3299.212000] drivers/usb/class/usblp.c: usblp0: removed
...