Only one IP: 192.168.1.103
Try putting it into /etc/sane.d/net.conf and then try scanimage -L
Try putting it into /etc/sane.d/net.conf and then try scanimage -L
-
This was the result. It is the only entry in that file:Originally posted by oshunluvr View Post
No scanners were identified. If you were expecting something different,
check that the scanner is plugged in, turned on and detected by the
sane-find-scanner tool (if appropriate). Please read the documentation
which came with this software (README, FAQ, manpages).
And yes, the scanner is turned on.
Comment
-
I have not followed this whole thread but has the op done the steps outlined here https://help.ubuntu.com/community/SA...0auto-detectedComment
-
Since nmap isn't picking it up and this didn't work, it seems like your router is blocking the connection between the two devices.Comment
-
Since nmap isn't picking it up and this didn't work, it seems like your router is blocking the connection between the two devices. Do you have a firewall enabled?Comment
-
No it is a fully Kubuntu machine right out of the box.Originally posted by oshunluvr View Post
http://www.sane-project.org/sane-mfgs.html] I took a look at this and there are a lot of HP units, mine is not listed. This does not make sense as the scanner was working fine on this version of Kubuntu previously. I'm wondering if I am using the right HPLP?Comment
-
-
There seems to be a problem with the nmap command options you gave.
I did the nmap command, and it did not detect my printer, nor my NAS, but I can ping them
marc@marc-lap:~/MyKubuntuCustomisation$ sudo nmap -sn 192.168.0.0/24
Starting Nmap 6.46 ( http://nmap.org ) at 2014-12-10 23:17 CET
Nmap scan report for 192.168.0.1
Host is up (0.021s latency).
MAC Address: 5C:35:3B:04:A4:9C (Compal Broadband Networks)
Nmap scan report for 192.168.0.156
Host is up.
Nmap done: 256 IP addresses (2 hosts up) scanned in 13.62 seconds
marc@marc-lap:~/MyKubuntuCustomisation$ ping 192.168.0.100
PING 192.168.0.100 (192.168.0.100) 56(84) bytes of data.
64 bytes from 192.168.0.100: icmp_seq=1 ttl=255 time=2.36 msJe suis Charlie, how many more people have to die for religions
linux user #447706 on https://linuxcounter.net
A good place to start: Topic: Top 20 Kubuntu FAQs & Answers
Comment
-
Well, you can see my nmap results. Everything on my network shows up - wired or un-wired - all through a power-line ethernet set, a 16 port switch and a router with wireless all the away across the house.Comment
-
-
-
Are you using an older version of Kubuntu? The command used to be nmap -sP...Originally posted by mbohets View PostComment
-
Got a long output but I think the key line is:Originally posted by oshunluvr View Post
warning: Printer is not HPLIP installed. Printers must use the hp: or hpfax: CUPS backend for HP-Devices.Comment
-
william78@william78:~$ ping -c 1 192.168.1.103Originally posted by oshunluvr View Post
PING 192.168.1.103 (192.168.1.103) 56(84) bytes of data.
64 bytes from 192.168.1.103: icmp_seq=1 ttl=255 time=11.5 ms
--- 192.168.1.103 ping statistics ---
1 packets transmitted, 1 received, 0% packet loss, time 0ms
rtt min/avg/max/mdev = 11.587/11.587/11.587/0.000 msComment
-
Well, it seems you can reach the printer but without hplip installed properly, you're not going to be scanning. Have you run hp-setup?Comment
Comment